User manual DAEWOO DMB-3003LH

[. . . ] SAFETY INSTRUCTIONS PLEASE READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE INSTALLING AND OPERATING THE UNIT: This air conditioner meets strict safety and operating standards. The installer of this unit must install or service this unit so it operates safely and efficiently. Precautions When Wiring: · Do not plug in the unit until all connections (tubing, drain hose, mounting, etc. ) have been made and double-checked. · High voltages are present in this unit and are very dangerous. Please refer to these instructions and diagrams when wiring. [. . . ] (Follow battery manufacturer's directions). CELSIUS TO FAHRENHEIT CONVERSION CHART CELSIUS 18 19 20 21 22 23 24 25 FAHRENHEIT 64. 4 66. 2 68 69. 8 71. 6 73. 4 75. 2 77 CELSIUS 26 27 28 29 30 31 32 FAHRENHEIT 78. 8 80. 6 82. 4 84. 2 86 87. 8 89. 6 CAUTION-IN CASE OF OPERATING TWO UNITS the operation mode of the remote controller CASE I indoor unit B1 indoor unit B2 Operation Fan Heating Heating Fan Cooling Heating Heating Cooling Fan Cooling Cooling Fan CASE II Cooling Cooling Cooling Dehumidification Dehumidification Cooling Good Heating Heating No Good As shown above, When the "CASE I" is selected, only the indoor unit which is received the first signal from the remote controller operates and the other indoor unit doesn't operate. also, you can see the blink of indicators of the latter. in that case, try to select one out of the "CASE II" again. 9 ­ + TO SET AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode. All you have to set is the desired temperature and it will control the fan, coolness and dehumidifier. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. Make sure the AUTO indicator AUTO appears in the remote display. or buttons, set the desired temperature. The desired temperature can be changed up or down 1 degree from the actual room temperature. For temperature setting: 24~28°C 3. Then the unit will automatically operate. AUTO TO SET QUICK MODE To set this unit to cool at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. Press the MODE button until the Quick indicator appears in the display. 3. The unit will then start cooling the room at the highest power. TO SET COOL MODE To set the unit to cool the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. or buttons, set the desired temperature. The desired temperature can be changed up to 32°C and down to 18°C. Press the MODE button until the Cool indicator appears in the display. 4. To select the fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). FAN SPEEDS AUTO "AUTO" "" "" "" "NATURAL" The fan will automatically select the fan speed. The fan will randomly cycle through the speeds simulating a cool breeze. 10 TO SET ONLY FAN MODE To operate only the fan so the unit will circulate the air, proceed as follows: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. Press the MODE button until the Fan indicator appears in the display. To select a fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). FAN SPEEDS "" "" "" "NATURAL" The fan will operate on low speed. [. . . ] · Some metal edges on the unit are sharp. · Internal parts in the outdoor unit may need cleaning or routine maintenance from time to time. Consult your local service center for more details. AFTER THE SEASON: · Operate the fan, then dry the indoor unit. · Shut off the indoor unit and then unplug it from the wall. [. . . ]