User manual DAEWOO DP-HG22

[. . . ] INSTRUCTION MANUAL DP-HG22 PLASMA MONITOR (DISPLAY) WALL HANGER UNIT H A N G E R U N I T W A L L Thank you for purchasing the Daewoo Electronic Plasma Display Wall Hanger Unit. This wall unit is specifically designed for use with the Daewoo Plasma Display. [. . . ] The wall hanger unit needs to be installed securely enough to handle earthquakes or lengthy periods of vibration. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) When assembling, do not use any parts other than those enclosed and secure all parts tightly. Do not leave out any part when assembling. Please install all parts to where indicated. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to vibrate and to fall) Do not alter or modify any parts Do not use the wall hanger unit with other products. This wall hanger unit is specifically designed to fit the Daewoo Plasma Display. (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) 3 PLASMA DISPLAY HANGER UNIT * PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING Special care is needed when installing onto the wall due to its weight (35Kg) When installing, please wear working gloves. When installing on a concrete wall Please be sure to use the enclosed concrete anchors. (If done with bare hands, it may result in injury) Be sure that no one is around to distract you during the installation process. When installing on a wooden wall take special care as the unit may require extra support to uphold the weight of the plasma display. (It may result in injury to you or others) When installing, please have at least two people. Please choose a wall that is straight so that the plasma display can be securely attached onto the wall. H A N G E R U N I T W A L L (Because of its weight, the unit may fall and can cause injury) Place a protective covering over the surface you will be working on when handling the plasma display and the wall hanger units. (If attached on an unstable wall, the unit can fall and break) After installing, please be sure to check to see if the unit has been secured firmly. (Failing to do so may result in unwanted marks on the unit) 4 * PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING When installing, please use the size referenced below to choose a place, and attach the paper pattern plan to the wall. 519. 5 519. 5 Paper pattern plan 314 314 . Measurement unit : mm It is important to use the paper pattern plan to choose the proper place; otherwise, it can result in damage to the wall and you will not be able to install the unit When installing, please allow at least 15 cm at the top, bottom, left and right on the wall, and clear all items away from where the unit will be. 15cm 15cm 15cm If proper spacing is not allowed, it may cause the plasma display to overheat, which can cause fire or damage to the unit 15cm 5 PLASMA DISPLAY HANGER UNIT 3. ASSEMBLING INSTRUCTIONS PREPARATION WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND 1 TO DETACH THE STAND FROM THE PLASMA DISPLAY . To avoid unwanted marks on the unit, place a protective covering over the surface you will be working on and lay the plasma display as shown below. . Unscrew the secured 2 screws completely and Pull the stand away from the plasma display to detach. 2 TO PLACE THE PROTECTIVE CAPS . There will be two holes where the stand has been detached. . Put the protective caps on the holes and use the screws to secure tightly. Caps H A N G E R U N I T W A L L Holes Screws 6 CORRIGENDA MODEL: DP-HG22 INSTALLING THE WALL FRAME SET A ON THE PLASMA DISPLAY PANEL . Replace the previous instruction (#2) with the following updated one. Four M5 screws are not used out of total number. Installation by professional is preffered. Contact infomation for any question. 1-800-DAEWOO-8 #8 1-201-964-9349 Service@daewoodigital. com 2 HOW TO INSTALL FRAME SET A ON THE UNIT . To avoid unwanted marks on the unit, place a protective covering over the surface you will be working on and lay the plasma display as shown in the picture below. . Place frame set A on the left and right side of the unit and use the enclosed screws (M5) to secure them tightly. (left and right 2 each) . When securing frame set A to the plasma display panel, make sure that they match the holes correctly. . If the holes are matched incorrectly, the installation will not be successful. 7 Note PLASMA DISPLAY HANGER UNIT INSTALLING WALL FRAME SET B AND CONNECTING FRAME 1 INSTALLING WALL FRAME SET B AND CONNECTING FRAME. Frame set B Connecting Frame . Place frame set B on the left and right side of the unit and use the enclosed screws (M5) to secure them tightly. Note . Please be sure to not force an . adjustment when connecting frame set B and connecting frame. [. . . ] . Please retain the two needed when modifying angle adjustment. At least two people are Note 2 THE FIGURES BELOW DISPLAY THE POSSIBLE PLASMA DISPLAY ANGLES. H A N G E R U N I T W A L L 0° 10° 15° 20° 12 [. . . ]