User manual DAEWOO DPC-3000N

[. . . ] DPC3000N Precaution Before you start IMPORTANT The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of unisulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing instructions in the literature accompanying the appliance. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Press for slow forward scanning during pause. PBC (Option key) Turn on and off the PBC function in video CD mode GO TO Used to go to the chapter, track or song on the disc you want. 3D Virtual 3D Sound Control SUB-T Changes the subtitle language to another available language or sets OFF (if the disc supports multiple subtitle languages). AUX (Option key) Changes the DVD mode and external A/V input mode AUDIO ONLY Turns off the screen for audio only mode (For the protection of LCD Monitor in Audio CD or MP3) AUDIO Changes the audio language to another available language (if the disc supports multiple audio languages). DIMMER Set the display brightness (HALF, FULL, OFF). ANGLE View with a different frame angle. (This button is available only on multiple angle DVDs. ) VOL+/VOL Increases and decreases the volume. DISPLAY Shows the information about time and play state. 17 Getting Started Power Connections 1 When using the Cigarette cable adaptor supplied. - Make sure that input voltage is only 12V - Connect to DC INPUT. DIGITAL OUT 1 L 2 DC IN 2. 5A, 12V DC OUT EXTERNAL MAX. 1. 5A, 12V REMOTE DIN S-VIDEO OUT VIDEO AUDIO R 2 When connecting the DC power cable. - DC cable - This installation should be made by a qualified service person and should confirm to all local codes. - Connect the terminal of red cable to DC only 12V, and the terminal of black cable to ground. 3 When using the DVD player at home - Connect to DC INPUT using an AC/DC adapter. *(optional) Note - When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections. - Connect the DVD player to your TV directly. If you connect the DVD player to a VCR, the playback picture will be distorted because DVD's video discs are copy protected. - Fuse Replacement Marking - Replace only with same type (3 A, 250 V) and ratings of fuse for continued protection against fire hazard. 18 Getting Started Connecting to a TV DIGITAL OUT 1 L L (White) R (Red) 2 R VIDEO AUDIO DC IN 2. 5A, 12V DC OUT EXTERNAL MAX. 1. 5A, 12V REMOTE DIN S-VIDEO OUT Audio Output S-Video Output Video Output (Yellow) Audio Input R Getting Started L Video Input S-Video Input Connect the DVD player to your TV 1 Connect the AUDIO CABLES between the AUDIO OUT L and R jacks on the back of your DVD player and the corresponding AUDIO INPUT jacks on your TV. 2 Connect the VIDEO CABLE between the VIDEO OUT jack on the back of your DVD player and the corresponding VIDEO INPUT jack on your TV. (have a SVIDEO jack on your TV, connect to the S-VIDEO jack on your player. Warning Do not set the Digital Audio Output of this DVD player to "SPDIF/PCM" unless you are connecting the DIGITAL AUDIO jack of this DVD player to an AV decoder that has Dolby Digital decoding function. High volume sound may damage your hearing as well as speakers. 19 Getting Started Connecting to a Car Audio System L (White) 1 L DIGITAL OUT R (Red) 2 DC IN 2. 5A, 12V DC OUT EXTERNAL MAX. 1. 5A, 12V REMOTE DIN S-VIDEO OUT VIDEO AUDIO R Audio Output Video Output (Yellow) TV or LCD Audio Input R L Video Input Connecting to a Car Audio System 1 Connect the AUDIO CABLES between the AUDIO OUT L and R jacks on the back of your DVD player and the corresponding AUDIO INPUT jacks on your audio system. 2 Connect the VIDEO CABLE between the VIDEO OUT jack on the back of your DVD player and the corresponding VIDEO INPUT jack on your TV. Note - When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the power source before making any connections. - If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, move the DVD player away from the tuner and radio. - Be sure to adjust the receiver's volume to a moderate listening level, otherwise, the speakers may be damaged by a sudden high volume sound. - Turn off the receiver before you connect or disconnect the DVD player's power cord. If you leave the receiver power on the speakers may be damaged. 20 Getting Started Connecting to a Dolby Digital System Coaxial Digital Out DIGITAL OUT 1 L 2 DC IN 2. 5A, 12V DC OUT EXTERNAL MAX. 1. 5A, 12V REMOTE DIN S-VIDEO OUT VIDEO AUDIO R Video Output Coaxial Cable S-Video Output Dolby Digital Decoder Coaxial Digital In Getting Started Center Speaker Front Speaker (L) TV Front Speaker (R) Sub Woofer Rear Speaker (Left surround) Rear Speaker (Right surround) Dolby Digital Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD with this dynamic realistic sound by connecting the DVD player to a 5. 1 channel receiver equipped with a Dolby Digital decoder or Dolby Digital processor. 1 Connect the COAXIAL DIGITAL OUT (black) jack on the back of your DVD player to the DIGITAL IN jack of the Decoder or AV amplifier. 2 Refer to pages 18-19 for details on video connection to TV. - When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. - Turn off the receiver before you connect or disconnect the DVD player's power cord. If you leave the receiver power on, the speakers may be damaged. Note 21 Basic Operation Playing DVD's Before Playing your DVD Ensure that your DVD player is connected correctly to the TV and audio system, which are output components. Turn on the power of the TV and audio system. Ensure that the local code of the DVD player is matched to that of the disc. If not matched, your disc cannot be played (refer to page 7). To Play a DVD 1 Press the POWER ( ) button. 2 Insert the DVD. Ensure that the labeled surface (not the surface where data is recorded) is at the top when placing it. 3 Your DVD will be automatically played depending on the current program mode. 1) The Disc menu is displayed on the screen. [. . . ] Cancel the rating function or change The rating level is set. 45 Additional Information Additional Information Cause The remote control doesn't work properly. Symptom Correction Point the remote control at the remote sensor of the DVD player. Operate the remote control within about 23ft (about 7m). Remove the obstacle. The remote control is not pointed at the remote sensor on the DVD player. [. . . ]