User manual DAEWOO DSA-9310E

[. . . ] USER'S MANUAL TV RECEIVER DSA-9310E CUST OMER HELPLINE NUMBER 0870 100 2525 PARTS INCLUDED IN THE BOX Remote control 1UNIT P/C Cable(optional) 1UNIT Audio Cable(optional) 1UNIT AC Cable 1UNIT 2 TABLE OF CONTENTS PARTS INCLUDED IN THE BOX TABLE OF CONTENTS SAFETY INSTRUCTIONS FRONT & REAR VIEW OF RECEIVER FRONT PANEL REAR PANEL CONNECTION GUIDE CONNECTING WITH MONITOR CONNECTING WITH AN AERIAL CONNECTING WITH ANOTHER SET TOP BOX OR VIDEO EQUIPMENT CONNECTING WITH PC REMOTE CONTROL PROGRAMME BANNNER VOLUME BAR FEATURES OF THE MAIN MENU TO START SET TO MUTE THE SOUND INSTANTLY AUTO TUNING MEMORY OF PROGRAM EDIT OF MEMORISED PROGRAM SKIPPING THE PROGRAMS POSITIONS DELETING THE PROGRAM POSITIONS MOVING THE PROGRAM POSITIONS MANUAL TUNING FINE TUNING WATCHING VIDEO PROGRAMS OPERATING PICTURE AND PICTURES PIP(PICTURE IN PICTURE) 2PIC(TWIN PICTURES) POP(PICTURE OUT PICTURE) OPERATING PAP BY MENU SOUND SETTING THE CLOCK TELETEXT TROUBLE SHOOTING SPECIFICATIONS 2 3 5 8 8 9 10 10 11 12 13 14 16 17 18 20 21 22 26 28 29 29 30 31 32 33 33 35 36 37 38 39 40 42 43 3 SAFETY INSTRUCTIONS Remove mains plug from socket when receiver is not in use for a long time or during a lightening storm. Do not place any liquid container on top of RECEIVER. If water spills into RECEIVER, an electric short may occur which can cause a fire. Do not handle the power cord with wet hands. Do not pull the power cord to remove the plug from the socket. It may cause an electric shock or damage. Do not overload wall outlets and extension cords. It may result in power failure. Do not make any modifications. Never attempt to disassemble the unit. When a strange noise or smell comes from the RECEIVER, stop all operations and pull out plug. [. . . ] Edit mode disappears automatically in several seconds or Pressing MENU button. 6 Check the memorised status by pressing PR buttons. Only memorised channels are selected. V/W 25 EDIT OF MEMORISED PROGRAM . The change is memorised automatically. Notice The EDIT menu shows you information as follows : . Program position assignment : PR number and Station name. Sound information : Auto, B/G, I, D/K1, D/K2, D/K3, L. 1 Select EDIT at the Tuning Menu. 26 2 After Moving the cursor by ARROW C / B buttons, select the information by ARROW V / W button. Ex) ENTER A STATION NAME . You can enter a station name with the V / W buttons. A letter from the Alphabet and Numbers will appear one-by-one. 3 Check the Edit status by pressing PR V / W buttons. " . The edit status appears in the PR banner. 27 SKIPPING THE PROGRAMS The programme marked with SKIP "YES" is skipped when changing channel using the PR V / W buttons. A skipped program number can be selected using the NUMBER button 0. . 9, These will be displayed in Red. Select SKIP "YES" or "NO" with the "SKIP (Red)"button. . You can also use the ARROW V / buttons after moving the cursor to Skip. W 28 DELETING THE PROGRAM POSITIONS . Position the selection bar to program number to delete with the V / W buttons. Press the "DELETE (Yellow)"button. MOVING THE PROGRAM POSITIONS . Position the selection bar to program number you want to move. Press the "MOVE(Green)"button. The colour of selection bar will be changed to Green. Position the new selection bar to new program number. Press the MOVE(Green) button. 29 MANUAL TUNING . If you are unable to get any programs because of a poor broadcasting signal, it is possible to store the Manual tuning. 1 Select manual tuning at the Install menu. 2 Press the Arrow C / B Buttons. A Tuning bar will move from left to right / from right to left. After searching a station, the tuning Bar will stop. If you want to stop tuning, press the MENU button. 30 3 Select programme number using the Press the "Green" button to store. V/W buttons and FINE TUNING . [. . . ] If you want to look at a subpage for a longer period of time, press the HOLD ( ) button. " appears beside page number and the contents of the subpage shown are kept on the screen and no longer updated or switched to other subpages. Pressing the HOLD button( ) again, the current subpage appear. 40 CALLING UP SUBPAGE DIRECTLY Pressing the SUBPAGE( ) button , " sub-code - - - - " appears beside page number. Enter the subpage number that you want to call up with the NUMBER button 0. . 9 , for example, the 2nd page, sequence 0002. [. . . ]