User manual DAEWOO DSJ-4720CRA

[. . . ] INSTRUCTION MANUAL DSJ-4710CRA / 5510CRA DSJ-4720CRA / 5520CRA PROJECTION TV CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. -1- IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. [. . . ] · The main power lamp turns on in red color. · Press the "Power" button of the main body or the "Power" button of the remote control. · The main power lamp turns on in "green" color and the TV turns on. POWER Press the " CH " button. · Select the desired channel by pressing the " CH " button or the number button. Ex) Channel 09 Air 09 Adjust volume. ·Sound reduces if pressing the VOL button. · Sound increases if pressing the VOL button. Vo l 9 Press the "Power" button for turning the TV off. POWER · TV turns off and the power lamp changes to red color. -25- Automatic Channel Memory Automatic Channel Memory - This is function for the TV to automatically memorize only the broadcasted channel. If setup the Auto Channel, you can simply find out channels with the channel " CH " button and so need not to select channels by pressing each channel number. - Always enter this function at the regular TV On-Air time with antenna connected. Air/Cable channel currently OnAir is memorized respectively if setup Auto channel for the General/Cable broadcasting. Always perform this process again if moving to another place or moving the TV. Press the "Menu" button. · The menu screen appears as follows. · Press the " VOL " button until the " " mark will come on the "Set up". · Press the "CH " button if the " " mark will come on the "Set up". Select the "Air/Cable" by pressing the " CH " button. · Select the "Air/Cable" by pressing the " CH " button. · Select "Air" to watch the general broadcasting, and select "Cable" to watch the cable TV by using the " VOL " button. -26- Select the "Auto Program". · Select the "Auto Program" with the " CH " button. Press the "VOL " button. · Pressing the "VOL " button automatically searches On-Air Channel as in the right. · On Air TV, searches from 2 channels through 69 channels, and on Cable TV, searches from 1 channels through 125 channels. · In this case, if pressing the menu button, the automatic Channel search is stop. However, channels searched by that time are saved. Auto Program is completed. · A screen appears as in the right if the Auto Program is completed. · A screen appears as in the paragraph 1 if pressing the menu button. · Continue to press the menu button until the menu screen disappears. Check by pressing the " CH " button. · Searches only the memorized channel. -27- Additional Channel Memory - This is method for additionally memorize channels not memorized due to weak broadcasting signal. - This function is available even in the <Menu> - <Set Up> - <Ch Edit> - <Add/Erase>. Select the Channel to memorize. · Select the Channel by pressing the number button. Ex) "13" channel Press the "Add/Erase" button. ADD/ ERASE · Add ­ Erase character alternatively appears whenever pressing this button. · Add appears in green color and Erase appears in red color. · Watch the memorized Channel with the " CH " button. Check the Channel by pressing the " CH " button. · "13" is selected by pressing the " CH " button. -28- Erase of Memorized Channel - This is function to erase unnecessary Channel memorized. - This function is available even in the <Menu> - <Set Up> - <Ch Edit> - <Add/Erase>. Select the Channel to erase. · The Channel to erase with the " CH " button. [. . . ] · Adjust blue color in the same manner. · Adjust the screen so that color of the middle cross becomes white in the length and the width. Press the "Menu" button. · Press the menu button until the menu screen disappears. · Ensure that color is correct by turning the channel. · Perform setup again if color is unmatched. [. . . ]