User manual DAEWOO DSJ-5040LDA

[. . . ] INSTRUCTION MANUAL DSJ-5040LDA PROJECTION MONITOR 1. Heading : "IMPORTABT SAFETY INSTRUCTIONS", before operating instructions. Explanation of graphical symbols (Lightning Flash and Exclamation Mark, Fig 15 DU) as follows, or equivalent, (a) Lightning Flash Symbol. with "The Lightning Flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons". [. . . ] Be careful of not crossing cables. -24- 3. Select VIDEO1-2-3 input using TV/VIDEO button on the remote control. Pressing TV/VIDEO button changes external channel as below. -25- PC Connection Connection with PC Modify the resolution and vertical frequency of PC as the supported those by TV before connecting. 1. Prepare cables(15pin D-sub or HDMI to DVI) 2. Connect TV with PC using the prepared cable as below. HDMI HDMI PC PC -26- 3. Select PC or HDMI input using ULTIMEDIA button on the remote control. Pressing ULTIMEDIA button changes external channel as below. DTV Format 480p 720p 1080i 640 480 600 768 1024 480 720 1080 480 600 768 1024 768 HDMI PC Format 800 1024 1280 720 1280 1920 640 DTV Format RGB PC Format 800 1024 1280 1360 60Hz 60Hz 30Hz 60Hz 75Hz 60Hz 75Hz 60Hz 75Hz 60Hz 60Hz 60Hz 30Hz 60Hz 75Hz 60Hz 75Hz 60Hz 75Hz 60Hz 60Hz OverScan No OverScan OverScan No OverScan 480i = 640 480 @ 30Hz 480p = 720 480 @ 60Hz 60Hz 59. 94Hz . 720p = 1280 720 @ 60Hz 1080i = 1920 1080 @ 30Hz DVI/HDMI cable cannot send audio signal in the contrast to HDMI/HDMI. In this case, cable for audio has to be connected additionally. -27- Connection with Dolby Digital Amp ( /PCM) -28- Name of Each Part Front Panel Side Panel Rear Panel ׳1 ׳2 1 2 Ʈ 1 Y -Է Pb/Cb Pr/Cr HDMI ( /PCM) Ʈ 2 PC -29- Remote Control DISPLAY POWER 100 BUTTON PREV CH MENU TV/VIDEO MULTIMEDIA CH / VOL SURROUND MUTE GUIDE POWER : Turns on/off the TV. Channel number(0~9) : Selects a channel. DISPLAY : Displays information on the TV screen. 100 BUTTON : Uses for channels over 100. PREV CH : Turns to the previous channel. SURROUND : Chooses the setting of speakers. MULTIMEDEA : Cycles through the video equipment connected to your TV s. CH / : Scans quickly through channels. MUTE : Mutes the sound. Press again or VOL to numute. GUIDE : Displays the TV s program guide. MENU : Brings up the main menu to the screen, or exit the main menu from the screen. TV/VIDEO : Cycles through the video equipment connected to your TV s video inputs. VOL / : Increases/decreases the sound level. -30- 30 SLEEP ADD/ERASE MTS SOUND MODE SCREEN SIZE PICTURE MODE PIP CAPTION STILL CH TV/VIDEO POSITION / SWAP SLEEP : Reserves turning TV off automatically. ADD/ERASE : Adds or Erases channels manually. SOUND MODE : Cycles repeatedly through the available sound modes. PICTURE MODE : Cycles repeatedly through the available video picture modes. STILL : Freezes the currently-viewed picture. [. . . ] Selecting channel to be memorized Pressing ADD/ERASE button makes the selected channel erased. 2 Erase memorized channel by following step. Selecting channel to be erased Confirm if the wanted channel was memorized by pressing up/down button Pressing ADD/ERASE button makes the selected channel erased. -43- Fine Tuning Fine Tuning This function is used to adjust and control the picture when the image of the screen displays dotted lines, distortion, lack of color, etc. It helps the television to output the clearest and highest quality picture. 1 Select Menu-Channel (act after selecting channel to be controlled) 2 act after selecting Fine Tuning Stop tuning at the best quality picture. -44- 1 2 -45- Watching external apparatus Watching VCR or camcorder Refer to the connection guide at page 24~27 1 Connect VCR or camcorder with TV and turn these on. 2 Select input by pressing TV/VIDEO button on remote control (TV-VIDEO1-VIDEO2-VIDEO3-TV) Picture changes as below by pressing TV/VIDEO button -46- 1 Connect DVD with TV and turn these on. [. . . ]