User manual DAEWOO DTQ-14D4AS

[. . . ] INSTRUCTION MANUAL Color T elevision DTQ 14D4AS DTQ 20D4AS SAFETY IMPORTANT SAFEGUARDS PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE TV RECEIVER. Unplug this television equipment from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this cable into a splitter (available at your local electronics store). Connect one coaxial cable between one OUT terminal on the splitter and the IN terminal on the converter box. Connect another coaxial cable between the other OUT terminal on the splitter and the B-IN terminal on an A/B switch (available at your local electronics store. ) Connect a third coaxial cable between the OUT terminal on the converter box and the A-IN terminal on the A/B switch. Finally, connect a coaxial cable between the OUT terminal on the A/B switch and the antenna terminal on the back of your TV. When the A/B switch is in the A position, you need to change channels on the converter box (and your B OUT TV should be tuned to channel 3 or 4); when the A/B switch is in the B position you can change channels on the TV. Connecting Other Pieces of Equipment You may want to connect a VCR, laser disc player, satellite receiver, or another type of equipment to your TV. We recommend that you follow the instructions included with the piece of equipment you wish to connect. OUT IN OUT IN OUT IN IN A Converter Box Safety Note If you plan on being away from your home for an extended period of time, or if a thunderstorm is approaching, you should unplug your television, and you may wish to disconnect your TV from a rooftop or satellite antenna. You do not need to disconnect your TV from a cable system. 10 Chapter 2 : Connecting an Antenna or Cable to Your TV Changing Channels You can change channels in three ways: 1 The CH buttons will take you through all memorized channels, one by one. The CH buttons will not access channels that have not been programmed into the TV's memory. For more information about programming channels into memory, see the section Programming your TV's Channel Memory on the previous page. The number buttons (0-9) will take you to any channel, even if it has not been memorized. To change to a channel, enter its number; the TV will tune to the new channel when you enter the second digit of the channel. The PREVIOUS button will take you instantly to the last channel you were watching. 2 3 Changing the Volume 1 2 To change the volume of the TV set, use the remote or on the front panel. VOL buttons on the To quickly turn off the sound, press the MUTE button on the remote. The MUTE will appear on screen, colored green. To return the volume to its previous level, press MUTE again. 12 Chapter 3: Operating Your TV Changing the TV's Input Normally, your TV displays the signal coming through the antenna terminal. However, If you ve connected another component to your TV(such as a VCR) using the Video/Audio input, you will want to be able to view the signal from the component. To do this, you will need to switch from the TV input to the Line Input, as follows. 1 With the TV on, press the MENU button twice, then set-up menu will appear. 2 Use the 3 Press the CH buttons to select Input . VOL 4 Wait 10 seconds, or press the MENU button to return to normal TV viewing. 1 2 3 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : Input : English Line Select Adjust Next When it connected an Video/Audio cable from the Video/Audio out jack on the VCR to the Video/Audio in jack on the front your TV, and your TV s back panel at the same time, the former takes precedence of the latter. 14 Chapter 3: Operating Your TV Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 With the TV on, press the MENU button. 2 Press the VOL buttons to set the Settings to Preset . The TV will remember the Custom settings you had previously chosen. [. . . ] · If there is neither picture or sound, unplug the TV for 30 seconds, then plug it in and try again. There is no picture or sound on some UHF channels. If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and is adjusted correctly. [. . . ]