User manual DAEWOO DTQ-14Q1FS

[. . . ] DTQ - 14Q1 / 20Q1 / 14Q2 / 20Q2 / 14Q1FS / 20Q1FS 14Q3 / 20Q3 / 14T1 / 20T1 / 14T1AS 14T2 / 20T2 / 14T3 / 20T3 / 21T1PS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION To provide power to the TV, insert the AC plug into a standard 110/220V, 50/60Hz polarized outlet. NOTE If you feel a static discharge when touching the unit, and the unit does not function, simply unplug the unit from the outlet. [. . . ] However, if you've connected another component to your TV (such as a VCR) using the Audio/Video Inputs, you will want to be able to view the signal from that component. To do this, you will need to switch from the "TV" input to the "Video" input, as follows; 1 With the TV turned on, Press MENU 2 You will see the Main Menu, Use the WCHV buttons to select Setup and press the CVOLB buttons. 4 Press the CVOLB buttons to change from TV to VIDEO. Press the CVOLB buttons again to switch back to TV. 5 Wait 10 seconds to return to normal viewing, or press the MENU button twice. When it connected an audio cable from the AUDIO out jack on the VCR to the AUDIO jack on the front your TV and your TV's back panel at the same time, the former takes precedence of the latter. Displaying the Current Channel 1 1 To quickly see the current channel, press RECALL. The current channel will be displayed briefly. Chapter 3 : Operating Your TV 15 Adjusting Video Settings You may wish to adjust the video settings (e. contrast or color) to obtain the most pleasing picture. To do so, follow these directions: 1 With the TV turned on, press the MENU button. 4 Use the WCHV buttons to select the video setting you wish to adjust. Descriptions of the video settings are on the next page. 1 2 Setup Video Timer 3 Video Picture Pref. Contrast Brightness Sharpness Color Tint Preset 4 Video Picture Pref. Contrast Brightness Sharpness Color Tint - |||||| ­ ­ ­ + |||| ­ ­ ­ ­ |||| ­ ­ ­ ­ |||| ­ ­ ­ ­ G­­­I­­­R L Prev WVMoveCBSelect L Prev WVSelect CBAdjust L Prev WVSelect CBAdjust 5 Use the CVOLB buttons to adjust the video setting to the level you prefer. 6 Use the WCHV buttons to select another video setting to adjust. 7 When you are finished, press the MENU button twice to return to normal viewing. 5 Video Picture Pref Contrast Brightness Sharpness Color Tint - |||||| ­ ­ ­ + 6 Video Picture Pref Contrast Brightness Sharpness Color Tint - |||||| ­ ­ ­ + 7 L Prev WVSelect CBAdjust L Prev WVSelect CBAdjust 16 Chapter 3 : Operating Your TV Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 Follow steps 1-3 in "Adjusting Video Settings" on the previous page. 2 Use the WCHV buttons to select Picture Pref. 3 Press the CVOLB buttons to set to Preset and Custom. These will return all video settings to their default level, as set at the factory. 4 Wait 10 seconds, or press the MENU button twice to exit. 1 Video Picture Pref. Contrast Brightness Sharpness Color Tint Preset 2 Video Picture Pref. Contrast Brightness Sharpness Color Tint Custom 3 L Prev WVSelect CBAdjust L Prev WVSelect CBAdjust If you set to Preset and Custom in direct mode, Use the AUTO. PICT button, follow these step: 1 2 3 Press the AUTO. [. . . ] If there is neither picture or sound, unplug the TV for 30 seconds, then plug it in and try again. There is no picture or sound on some UHF channels. · Try another station. If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and is adjusted correctly. · See if anything is interfering with the antenna signal. [. . . ]