User manual DAEWOO DTQ-19V4FC

[. . . ] INSTRUCTION MANUAL Color Television DTQ DTQ DTQ DTQ DTQ DTQ 13V1FC 19V1FC 13V4FC 19V4FC 13V5FC 19V5FC DTQ DTQ DTQ DTQ DTQ 13V6FC 19V6FC 13U1FC 19U1FC 14U5FC CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To prevent electrical shock, match wide blade of plug to wide slot, fully insert the AC plug into a standard 120V~, 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V~, 60Hz power. [. . . ] 4 If the channel is not in memory, then use the CVOLB buttons to add the channel from memory. 5 If the channel is in memory, then use the CVOLB buttons to delete the channel from memory. 6 If you are going to delete other channel, then press the VCHW buttons until desired channel is selected. And press the CVOLB buttons to delete the channel. 7 Wait 10 seconds, or press the MENU button to return to normal TV viewing. 1 2 3 11 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next 4 5 6 Add/Delete Channels Air 11 This channel is not in memory. Press CH for other channels. Add/Delete Channels Air 11 This channel is in memory. Press CH for other channels. Add/Delete Channels Air 11 This channel is in memory. Press CH for other channels. Press MENU to return to Set-Up menu. Press MENU to return to Set-Up menu. Press MENU to return to Set-Up menu. Displaying the Current Channel 1 To quickly see the current channel number and status, press DISPLAY button on the remote control. The current channel number and status will be displayed. Chapter 3 : Operating Your TV 13 Changing the TV's Input Normally, your TV displays the signal coming through the antenna terminal. However, If you've connected another component to your TV(such as a VCR) using the Video/Audio input, you will want to be able to view the signal from the component. To do this, you will need to switch from the `TV' input to the ` Line ` Input, as follows. 1 With the TV on, press the MENU button twice, then " Set-Up " menu will appear. 2 Use the VCHW buttons to select " Input ". 3 Press the CVOLB buttons to change from `TV' to ` Line `. 4 Wait 10 seconds, or press the MENU button to return to normal TV viewing. 1 2 3 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : Input : English Line Select Adjust Next When it connected an Video/Audio cable from the Video/Audio out jack on the VCR to the Video/Audio in jack on the front your TV, and your TV's back panel at the same time, the former takes precedence of the latter. 14 Chapter 3 : Operating Your TV Adjusting Video Settings You may wish to adjust the video settings (e. contrast or color) to obtain the most pleasing picture. To do so, follow these directions: 1 With the TV on, press the MENU button. then "Video" menu will appear. 2 The "Settings" item will be selected. Use the CVOLB buttons to turn Settings to Preset or Custom. 3 Use the VCHW buttons to select the video setting you wish to adjust. Descriptions of the video settings are on the next page. [. . . ] · If there is neither picture or sound, unplug the TV for 30 seconds, then plug it in and try again. There is no picture or sound on some UHF channels. If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and is adjusted correctly. [. . . ]