User manual DAEWOO DTQ-20T1

[. . . ] INSTRUCTION MANUAL C o l o r Te l e v i s i o n DTQ DTQ 14Q1 20Q1 DTQ DTQ 20T1 21T1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CONTENTS Table of Contents Important Safeguards Chapter 1: Overview of Your Equipment Your TV's Front Panel Your TV's Back Panel Your Remote Control Installing your remote control batteries Notes 2 4 4 5 6 7 7 Chapter 2: Connecting an Antenna or Cable to Your TV Connecting an Antenna Connecting a Cable System Connecting Other Pieces of Equipment Safety Note 8 8 9 10 10 Chapter 3: Operating Your TV Turning your TV On Programming Your TV's Channel Memory Changing Channels Changing the Volume Changing The TV's Channel Memory Adding a channel to memory Erasing a channel from memory Changing the TV's channel memory with the menus Changing the TV's Input Displaying the Current Channel Adjusting Video Settings Returning to factory settings Descriptions of video settings 11 11 11 13 13 13 13 14 14 15 15 16 17 18 Chapter 4 : Setting the Audio Changing the Sound Mode About AVC About Loudness 19 19 19 19 Chapter 5: Using Timer Functions Accessing the Timer Menu Setting the Clock Setting the On Timer Setting the Off Timer Canceling the On Timer or Off Timer Setting the Sleep Timer 20 20 20 21 22 22 23 Chapter 6 : Additional Features Changing the Language of the On-Screen Menus Captioning About captions Power restore Changing the TV's favorite channel memory with the menus Protection Features Automatic power off 24 24 24 25 25 26 26 26 Chapter 7 : Troubleshooting Warranty Table of Contents 27 28 1 SAFETY IMPORTANT SAFEGUARDS PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT AND RETAIN FOR FUTURE REFERENCE. [. . . ] The only DTQ-20/21T1 had to notice as follow: When it connected an audio cable from the AUDIO out jack on the VCR to the AUDIO jack on the front your TV and your TV's back panel at the same time, the former takes precedence of the latter. If it received an audio mono signal from another component, such as a VCR at this time, we must connect an audio Y cable from the AUDIO out jack on the VCR to the AUDIO jack on the front your TV. Equipment with Mono sound Output Displaying the Current Channel 1 1 To quickly see the current channel, press RECALL. The current channel will be displayed briefly. Chapter 3 : Operating Your TV 15 Adjusting Video Settings You may wish to adjust the video settings (e. contrast or color) to obtain the most pleasing picture. To do so, follow these directions: 1 With the TV turned on, press the MENU button. 4 Use the WCHV buttons to select the video setting you wish to adjust. Descriptions of the video settings are on the next page. 1 2 Setup Video Audio Timer 3 Video Picture Pref. Contrast Brightness Sharpness Color Tint Preset 4 Video Picture Pref. Contrast Brightness Sharpness Color Tint - |||||| ­ ­ ­ + |||| ­ ­ ­ ­ |||| ­ ­ ­ ­ |||| ­ ­ ­ ­ G­­­I­­­R L Prev WVMoveCBSelect L Prev WVSelect CBAdjust L Prev WVSelect CBAdjust 5 Use the CVOLB buttons to adjust the video setting to the level you prefer. 6 Use the WCHV buttons to select another video setting to adjust. 7 When you are finished, press the MENU button twice to return to normal viewing. 5 Video Picture Pref Contrast Brightness Sharpness Color Tint - |||||| ­ ­ ­ + 6 Video Picture Pref Contrast Brightness Sharpness Color Tint - |||||| ­ ­ ­ + 7 L Prev WVSelect CBAdjust L Prev WVSelect CBAdjust 16 Chapter 3 : Operating Your TV Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 Follow steps 1-3 in "Adjusting Video Settings" on the previous page. 2 Use the WCHV buttons to select Picture Pref. 3 Press the CVOLB buttons to set to Preset and Custom. These will return all video settings to their default level, as set at the factory. 4 Wait 10 seconds, or press the MENU button twice to exit. 1 Video Picture Pref. Contrast Brightness Sharpness Color Tint Preset 2 Video Picture Pref. Contrast Brightness Sharpness Color Tint Custom 3 L Prev WVSelect CBAdjust L Prev WVSelect CBAdjust If you set to Preset and Custom in direct mode, Use the AUTO. PICT button, follow these step: 1 2 3 Press the AUTO. Wait 3 seconds to exit. 1 Picture Pref. Custom Preset Chapter 3 : Operating Your TV 17 Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen. If the light areas are too bright and are losing details, adjust the contrast towards the "-" position; if the picture is gray and lacks contrast, adjust the contrast towards the "+" position. The brightness settings controls the overall amount of light in the picture. [. . . ] If there is neither picture or sound, unplug the TV for 30 seconds, then plug it in and try again. There is no picture or sound on some UHF channels. · Try another station. If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and is adjusted correctly. · See if anything is interfering with the antenna signal. [. . . ]