User manual DAEWOO DTQ-25G1TS

[. . . ] INSTRUCTION MANUAL C o l o r Te l e v i s i o n DTQ DTQ 25G1TS 29G1TS P/N : 48586217E208-R0 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION To provide power to the TV, insert the AC plug into a standard 120V , 60Hz outlet. NOTE If you feel a static discharge when touching the unit, and the unit does not function, simply unplug the unit from the outlet. When you plug the unit back in, it should work normally. [. . . ] Press the MENU button twice or wait few seconds to return to normal TV viewing. Your setting will remain intact until you change it. Your TV will then automatically reproduce either stereo or monaural sound, whichever is broadcast. Listening to second Language 1. Follow steps 1~3 in "Listening to stereo sound" above. Press the CVOLB buttons repeatedly until "SAP" is displayed. Press the MENU button twice or wait few seconds to return to normal TV viewing. If a SAP broadcast is received, you will hear only the second language from the speaker. About AVC This function performs an Automatic Volume Control Function. the sound signal conditions coming out of TV stations are different from each other. Some signals are intense and other are not . When the AVC is on, uniform sound can be ensured regardless of the conditions of TV station. Audio Audio Mode AVC Loudness On L Prev WVSelect CBAdjust About Loudness This function performs a bass and treble boost when the volume control is low position. When the Loudness is On, you can hear the dynamic sounds for a movie or music. Audio Audio Mode AVC Loudness On L Prev WVSelect CBAdjust Chapter 3 : Operating Your TV 20 Using Direct button on the remote control. 1. You can also change the Audio Mode setting with the remote control. Press the MTS button on the remote control to select Audio Mode. Use this button to select the Stereo, Mono or SAP. 1 Audio Mode Stereo Mono SAP Present Broadcast MONO MONO STEREO STEREO and SAP STEREO and SAP Your Selection Stereo SAP SAP Stereo SAP Speaker Out Mono Mono Mono Stereo SAP Note>If a broadcast signal is weak, it may cause noise and hum in stereo sound. Please select the Mono mode, the noise and hum should be reduced. 21 Chapter 3 : Operating Your TV Convenient Remote Function. Display On-Screen information. Press "Recall" button on the remote control to display on screen information of channel number or VIDEO mode. BCh12 Ch14 Note) When you Displayed PIP picture, the Recall button can select the Main or PIP display for changing channels. (See Chapter 5. for details) To Move cursor : RECALL CH12 BCh14 To Move cursor : RECALL Muting the Sound Press MUTE button on the remote control to mute the sound. The word "Muted" will display on the screen. To restore the sound, press MUTE again. Volume 24 C||||||||||| - - - - - - -B Muted Chapter 3 : Operating Your TV 22 CHAPTER 4 Using the Advanced Features. Changing the Language of the On-screen Menus You can choose to display the on-screen menus in English, Spanish or French. With the TV turned on, press the MENU button. Use the WCHV buttons to select Setup and press CVOLB. Use the CVOLB button to select the language you want to use : English, Spanish or French. [. . . ] · Check that the antenna is connected and is in good working order, has no broken wires, and is adjusted correctly. The picture is OK, but the sound is poor. If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and adjusted correctly. [. . . ]