User manual DAEWOO DTQ 25S2FCV

[. . . ] INSTRUCTION MANUAL C o l o r Te l e v i s i o n yyy yyy , , , , , , yyy yyy , , , , , , DTQ 25S2FCV DTQ 27S2FCV CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). [. . . ] 5 Wait 7 seconds to return to normal viewing, or press MENU twice. 1 2 3 4 Changing the TV's Input with the remote control 1 1 You can also change the TV/VIDEO setting with the remote control. Press TV/VIDEO button on the remote control to change from TV to VIDEO. Press TV/VIDEO button again to switch back to TV. Displaying the Current Channel 1 1 To quickly see the current channel, press RECALL. The current channel will be displayed briefly. Chapter 3 : Operating Your TV 13 Adjusting Video Settings You may wish to adjust the video settings (e. contrast or color) to obtain the most pleasing picture. To do so, follow these directions: 1 With the TV on, press the MENU button. 2 Use the VCHW buttons to select PICTURE. Use the CVOLB button to turn AUTO to OFF. This will allow you to manually adjust the video settings. 1 2 3 4 5 Use the VCHW buttons to select the video setting you wish to adjust. Descriptions of the video settings are on the next page. 6 Use the CVOLB buttons to adjust the video setting to the level you prefer. 7 Use the VCHW buttons to select another video setting to adjust. 8 When you are finished, press the MENU button twice to return to normal viewing. 5 6 7 8 14 Chapter 3 : Operating Your TV Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 Complete steps 1-3 in the "Adjusting Video Settings" section, on the previous page. 2 Press the CVOLB buttons to set the AUTO setting to ON. This will return all video settings to their default levels, as set at the factory. 3 You can also return to the factory settings during normal TV viewing by pressing the AUTO. PICT button on the remote control. The TV will remember the "custom" settings you had previously chosen. When you set AUTO to OFF again, your previous custom settings will be restored. 1 2 3 Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen. If the light areas are too bright and are losing details, adjust the contrast towards the "-" position; if the picture is gray and lacks contrast, adjust the contrast towards the "+" position. The brightness settings controls the overall amount of light in the picture. If the picture is too bright, adjust the brightness setting towards the "-" position; if the picture is too dark, adjust the brightness towards the "+" position. Sharpness controls how the TV displays edges of objects on-screen. [. . . ] · Check that the antenna is connected, is in good working order, has no broken wires, and is adjusted correctly. · See if anything is interfering with the antenna signal. · Make sure the AIR/CABLE setting is correct. The sound is OK, but the picture is poor. · Try another station. If the other stations are OK, it may be a station problem. [. . . ]