User manual DAEWOO DTQ-26S1FC

[. . . ] INSTRUCTION MANUAL C o l o r Te l e v i s i o n CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). [. . . ] 3 Use the VCHW buttons to select ANTENNA, then use the CVOLB buttons to select AIR or CABLE. If you connected an antenna to your TV, select AIR; if you connected a cable system, select CABLE. 4 Use the VCHW buttons to select AUTO PROGRAM, then use the CVOLB button to begin the AUTO PROGRAM process. 5 Press the MENU button to return to normal TV viewing. Your TV's channel memory will not be affected by a power outage. You will not need to re-program the memory unless you change the type of cable antenna connected to your TV. 1 2 3 4 10 Chapter 3 : Operating Your TV Changing Channels You can change channels in three ways: 1 2 1 The VCHW buttons will take you through all memorized channels, one by one. The VCHW buttons will not access channels that have not been programmed into the TV's memory. For more information about programming channels into memory, see the section "Programming your TV's Channel Memory, " above. 2 The number buttons (0-9) will take you to any channel, even if it has not been memorized. To change to a channel, enter its number; the TV will tune to the new channel when you enter the second digit of the channel. CH button will take you instantly to the last channel you were watching. 3 Changing the Volume 1 2 1 To change the volume of the TV set, use the CVOLB buttons on the remote or on the front panel. 2 To quickly turn off the sound, press the MUTE button on the remote. The volume bar will appear on screen, colored red. To return the volume to its previous level, press MUTE again. Changing the TV's Channel Memory Your TV's memory determines the channels that are available using the VCHW buttons. You can add channels to this memory or remove them from memory. If a channel is removed from memory, you can tune to it with the number buttons, but you cannot tune to it with the VCHW buttons. Adding a channel to memory 1 2 1 Use the number buttons to tune to the channel. 2 Press the ADD/ERA button on the remote control. The channel will turn from magenta to green to show it has been added. Chapter 3 : Operating Your TV 11 Erasing a channel from memory 1 2 1 Tune to the channel you want to erase. 2 Press the ADD/ERA button on the remote control. The channel will turn from green to magenta to show it has been erased. Changing the TV's channel memory with the menus You can also use the menu system to add or erase channels from memory: 1 Use the number buttons to tune to the channel, then press MENU. 2 Use the VCHW buttons to select SETUP and press CVOLB. 3 Use the VCHW buttons to select EDIT PROGRAM. [. . . ] If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and is adjusted correctly. · See if anything is interfering with the antenna signal. · Make sure the AIR/CABLE setting is correct. The sound is OK, but the picture is poor. · Try another station. [. . . ]