User manual DAEWOO DTQ-27U1SC

[. . . ] INSTRUCTION MANUAL COLOR TELEVISION DTQ-27U1SC DTQ-27U4SC DTQ-27U1SCV DTQ-27U4SCV CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To prevent electrical shock, match wide blade of plug to wide slot, fully insert the AC plug into a standard 120V AC, 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V AC, 60Hz power. [. . . ] Make sure your TV is plugged in before you try to turn it on. Programming Your TV's Channel Memory Your TV's memory determines the channels that are available using the WCHV buttons. If a channel is not in memory, you can tune to it with the number buttons, but not with the WCHV buttons. Follow these steps to program your TV's memory: 1 With the TV on, press the MENU button. Then press the CVOLB buttons until "Set-Up" menu will be displayed. 2 Use the WCHV buttons to select "Reception" item, then use the CVOLB buttons to select `Air' or `Cable'. If you connected an antenna to your TV, select `Air'; If you connected a cable system, select `Cable'. 3 Use the WCHV buttons to select "Memorize Ch. ", then use the CVOLB buttons to enter the "Memorize Ch. " process. 4 If you want to stop the "Memor ze Ch. " process, press the MENU button to return to Set-Up menu. 5 Wait 15 seconds, or press DISPLAY button or MENU button to return to normal TV viewing. Your TV's channel memory will not be affected by a power outage. You will not need to re-program the memory unless you change the type of cable or antenna connected to your TV. h h h h h h h h h h 15 Chapter 5 : Operating Your TV Changing Channels You can change channels in three ways: 1 2 3 1 The WCHV buttons will take you through all memorized channels, one by one. The WCHV buttons will not access channels that have not been programmed into the TV's memory. For more information about programming channels into memory, see the section "Programming your TV's Channel Memory" on the previous page. The number buttons (0-9) will take you to any channel, even if it has not been memorized. To change to a channel, enter its number; the TV will tune to the new channel when you enter the second digit of the channel. The PREVIOUS button will take you instantly to the last channel you were watching. 2 3 Changing the Volume 1 2 2 1 To change the volume of the TV set, use the CVOLB buttons on the remote controller or on the front panel. To quickly turn off the sound, press the MUTE button on the remote. To return the volume to its previous level, press MUTE again. Chapter 5 : Operating Your TV 16 Changing the TV's Channel Memory Your TV's memory determines the channels that are available using the WCHV buttons. You can add channels to this memory or remove them from memory. If a channel is removed from memory, you can tune to it with the number buttons, but you cannot tune to it with the WCHV buttons. If there are just one channel memorized, then the Add/Delete Channels function will search the whole channels. But if there are two or more channel memorized, then the Add/Delete Channels function will search the memorized channels only. [. . . ] If the other stations are OK, it may be a station problem. · Check that the antenna is connected, is in good working order, has no broken wires, and adjusted correctly. There is poor reception on some channels. If the other stations are OK, it may be a station problem. [. . . ]