User manual DAEWOO DTQ-29U9FS

[. . . ] INSTRUCTION MANUAL Color Television DTQ 29U9FS 29X9FS DTQ P/N:48586789E208-R0 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). [. . . ] · In case of main window and single/twin windows/multi windows, sound of main window is available through this function. · Adjust the volume of the headphone at a proper level. · Even while the sound of the main window is mute, the sound is available through the headphone. Sound Audio Mode Mono Balance 50:50 AVC Off Equalizer Headphone Volume 50 Woofer 50 Move Adj. Prev. 27 Open Function Menu Accessing to "Sound" sub-menu: 1. Press "MENU" button ·When this button is pressed, the screen appears as follows. Picture LEnjoy programs with selected modes by using various functions. Move Sel. Exit CB 2. Select "Sound" menu by using "VOLUMEC/B" buttons. ·Move the cursor to the "Sound" menu by using "VOLUMEC/B" buttons. ·Press "Channelx" button. Sound Move Sel. Exit Sound Audio Mode Mono Balance 50:50 AVC Off Equalizer Headphone Volume 50 Woofer 50 ·Then the following picture will be appeared on the screen. Move Sel. Prev. LSound reception of the main or an auxiliary window is available through Headphone. xy 3. Press "CHANNELx/y" buttons. Sound Audio Mode Mono Balance 50:50 AVC Off Equalizer Headphone Volume 50 Woofer 50 Move Sel. Prev. ·"Sound" mode is selected and its sub-menu appears. ·Continue to press "CHANNELx/y" buttons, and the selected sub-menu sign changes into blue color in the following sequence : Audio Mode Balance AVC Equalizer Heaphone Volume Woofer ·Continue to press "VOLUMEC/B" buttons at a submenu you want. 4. Press "MENU" button twice. ·Press this button one time, and menu window appears. Press it again, and you get the previous status of menu window. (Menu disappears) 28 Adjusting the Picture Adjusting Picture Quality LUsers do not need to handle many operation units in adjusting the picture on the screen. Just make one of the selections already built in by the company's experts. 1. Press "AUTO PICTURE" button ·The following pictures appear on the screen in sequence and the picture adjustment state is changed. <For pressing "AUTO PICTURE" button once> Strong <For pressing "AUTO PICTURE" button many times> Off Soft Standard 2. Use this mode and get quality pictures on the screen. ·Starting from a picture above, choose a proper picture quality you want by using "VOLUMEC/B" buttons. ·Picture adjustment is also possible in each "Video" mode. (Video1, Video2, Video3, Game) ·Picture adjustment is also possible in each "S-Video" mode. (S-Video1, 3) Off 29 Picture Noise Reduction 1. Press "MENU" button. ·Then the screen appears as follows : LWeak transmission signals could cause bad picture or noise. LThis function corrects this type of problem. Picture Move Sel. Exit x 2. Select "Picture" by using "CHANNELx" button. Picture Brightness Contrast Sharpness Color Tint Picture NR 50 90 50 50 50:50 Off ·Move the cursor to the "Picture" menu by using "CHANNEL x" button. LFor eliminating Picture noise press select "On" in "Picture NR" mode among "Function" sub-menu. Move Adj. Prev. xy 3. Press "CHANNELx/y" buttons. Picture Brightness Contrast Sharpness Color Tint Picture NR 50 90 50 50 50:50 Off Move Sel. Prev. ·When "Picture" mode is selected, its sub-menu appears on the screen. ·Continue to press "CHANNELx/y" buttons, and entries of this sub-menu turns blue in the sequence as follows : Brightness Contrast Sharpness Color Tint Picture NR ·Select "Picture NR" function by using "VOLUMEC/B" buttons, and then "On" and "Off" repeat in turn. Press "MENU" button twice. ·Press this button one time, and menu window appears. [. . . ] Press "MENU" button ·Then the screen appears as follows. LYou can adjust the state of screen according to light and surrounds automatically. Picture Move Sel. Exit CB 2. Press "Special" by using "VOLUMEC/B" buttons ·Move the cursor to the "Special" menu by using "VOLUMEC/B" buttons. ·Press "CHANNELx" button. Special Move Sel. Exit xy 3. Select "Digital Sensor" by using "CHANNELx/y" buttons. Special Surround Digital Sensor ·Setup "Digital Sensor" to turn "On". On On Move Sel. Prev. 52 Connecting VCR or Other AV sets Names of Connection Units and Their Functions BWhen the TV set is in Video Mode, Monitor transmits Video signal out. 53 Interface with Video Connection Unit on the back of TV set, and that of VCR set 1 Prepare Picture/Sound connection codes (accessories for separate sale). 2 Connect "Picture Out" unit of VCR set with "Picture In" of TV set. 3 Connect "Sound Out" unit of VCR set with "Sound In" of TV set. 4 Convert TV set to Video mode by pressing "TV/Video" button of Remote Control LThe Video set can be connected with either Video 1 or Video 2 jack of TV set. BThe way to connect is the same as that of connecting the back unit of TV set. [. . . ]