User manual DAEWOO DTQ-3282SCS

[. . . ] INSTRUCTION MANUAL DTQ-3282SCS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). [. . . ] Select "Picture" by using "CHANNELx" button. Picture : Dynamic Brightness Contrast Sharpness Color Tint Picture NR Move Adj 50 90 75 50 50:50 Off Prev ·Move the cursor to the "Picture" menu by using "CHANNEL x" button. LTo eliminate or reduce picture noise, press to select "On" in "Picture NR" mode of "Picture" sub-menu. xy 3. Press "CHANNELx/y" buttons. Picture : Dynamic Brightness Contrast Sharpness Color Tint Picture NR Move Adj 50 90 75 50 50:50 Off Prev ·When "Picture" mode is selected, its sub-menu appears on the screen. ·Continue to press "CHANNELx/y" buttons, and the entries of this sub-menu turn blue in the sequence as follows : Brightness Contrast Sharpness Color Tint Picture NR ·Select "Picture NR" function by using "VOLUMEC/B" buttons, and then, "On" and "Off" repeat in turn. Press "MENU" button twice. ·Press this button one time, and the menu window appears. Press it again, and you will get the previous status of the menu window. (Menu disappears) 20 Adjusting the Picture Screen to Your Preference LAccording to the user's preference, brightness, contrast, sharpness, color, and tint can be adjusted for each of AV1, AV 2, AV3 and TV mode. 1. Press "MENU" button. ·Then the screen appears as follows: Brightness: ·Adjusts the degree of brightness or darkness of the whole screen. Contrast: ·Adjusts (controls) the degree of brightness between the objects and background of the picture. x 2. Select "Picture" by using "CHANNELx" button. Picture : Dynamic Brightness Contrast Sharpness Color Tint Picture NR Move Adj Sharpness: ·Adjusts the shapes of objects in the picture, making them appear softer (blurred) or sharper (clean). 50 90 75 50 50:50 Off Prev Color: ·Adjusts the degree of color saturation. ·"Picture" mode is selected, and its sub-menu appears. ·Continue to press "CHANNELx/y" buttons, and the selected sub-menu sign changes into a blue bar in the following sequence : Brightness Contrast Sharpness Color Tint Picture NR ·Press the "CHANNELx/y" buttons, and capture "Tint" on the blue bar. Tint: ·Adjusts to produce the proper natural color of objects. 21 CB 3. Adjust "Tint" by using "VOLUMEC/B" buttons. Picture : Dynamic Brightness Contrast Sharpness Color Tint 50 Picture NR Move Adj 50 90 75 50 50 Off Prev ·Press "VOLUMEC" button, and the green tint increases. ·Press "VOLUMEB" button, and the red tint increases. ·To adjust other functions such as brightness, etc. , select the function you want by using "CHANNELx/y" buttons, and adjust the mode as above. Tint 32 32 CB 4. Adjust "Brightness" by using "VOLUMEC/B" buttons Picture : Dynamic Brightness Contrast Sharpness Color Tint Picture NR Move Adj 50 90 75 50 50:50 Off Prev ·Press "VOLUMEB" button for the Brightness to increase. ·Press "VOLUMEC" button for the Brightness to decrease. Brightness 50 5. Press "MENU" button twice. ·Press this button one time, and the menu window appears. ·Press it again, and the previous status of the menu window appears. ·To adjust other functions such as brightness, etc. , select the function by using "CHANNELx/y" buttons, and adjust them by using "VOLUMEC/B" buttons. 22 ADJUSTING THE SOUND Customizing the Audio 1. Press "MENU" button. ·Then, the screen appears as follows : "Balance" LThis function balances the volume between left and right speakers. L"Balance" adjusting screen appears as follows: CB 2. Select "Sound" menu by using "VOLUMEC/B" buttons. ·Move the cursor to the "Sound" menu by using "VOLUMEC/B" buttons. ·Press "CHANNELx" button. L"VOLUME UPB" keeps the volume of the right speaker as it is, but decreases the volume of the left one. "VOLUME DOWNC" keeps that of the left one as it is, but decreases that of the right one. Sound Balance LR Mode AVC Equalizer Dynamic Effect Move ·Then, "Sound" menu and its sub-menu appears. 50:50 Stereo Off Off Adj Prev "Equalizer" LThis function adjusts the range of quality sound of speakers. xy 3. Select "Equalizer" by using "CHANNELx/y" buttons. Sound Balance LR Mode AVC Equalizer ( Dynamic Effect Move 50:50 Stereo Off Off Adj Prev ·Capture "Equalizer" on the blue bar by using "CHANNELx/y" buttons. 23 CB 4. Select Range of Sound by using "VOLUMEC/B" buttons. Equalizer +12 -12 Adj Move Prev ·"CHANNELx" strengthens the selected range of sound. [. . . ] If a correct code was entered, the component will turn on. (If the component does not turn on, repeat the step 4 using another code. ) 5. Press the "Mode" button, and then, LED lamp will blink three times and go out. NOTE : Your component may not be compatible with the HDTV Monitor's remote control. [. . . ]