User manual DAEWOO DV-K486N

[. . . ] Video Cassette Recorder User's Guide DV-K486N/K286N As an ENERGYSTAR Partner, DAEWOO has determined that this product meets the ENERGYSTAR guidelines for energy efficiency. R R Safety information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] If this should happen, select 1 or 2 for the system you have. Press 1 to select Auto Channel Search mode and press 3 to detect the channel automatically and the scanning channel number appears. Wait until the channel numbers stop changing. (one to two minutes). AUTO CHANNEL SEARCH 6 When you are finished removing channels, press MENU three times to exit from the menus. Adding channels to memory If you have removed a channel from memory, you can easily add it back again. To add channels: 1 Now scanning channel 14 Press any key to cancel 4 Press ­CH/TRK+ to view the memorized channels. Use 0-9 to tune to the channel you would like to add. 3 Press 3 to select Channel Set. 2 CHANNEL SET Removing channels manually To erase a channel manually, 1 Press MENU to display the menu. 2 Press 3 to select Channel Set. CHANNEL SET 1 Auto Channel Search 2 Add/Remove Channels 3 Signal Type : CABLE Press MENU to exit 4 Press 2 to select Add/Remove Channels. ADD/REMOVE CHANNELS 1 Auto Channel Search 2 Add/Remove Channels 3 Signal Type : CABLE Press MENU to exit Channel 06 is now REMOVED. Press DISPLAY to add Press MENU to exit 3 Press 2 to select Add/Remove Channels. ADD/REMOVE CHANNELS 5 Press DISPLAY to add the channel. ADD/REMOVE CHANNELS Channel 06 is now ADDED. Press CLEAR to remove Press MENU to exit Channel 06 is now ADDED. Press CLEAR to remove Press MENU to exit 4 Use 0-9 to enter the channel you want to remove. 6 Press MENU three times to exit from the menus. 16 15 Daewoo Video Cassette Recorder User's Guide Daewoo Video Cassette Recorder User's Guide Using video cassettes Audio-visual material may include works of copyright which must not be recorded without authorization of the copyright owner. Watching recorded programs To watch a program recorded on a video cassette tape: ·Turn on the television. ·If your television is connected to: ­ an antenna, set the viewing mode to "ANTENNA. " ­ a cable system, set the viewing mode to "CABLE. " ·Turn the television to your VCR channel (either 3 or 4). ·Insert a video cassette. Before you play or record on a video cassette tape, be certain to read this information on the proper care and use of video cassettes. Only use video cassettes that bear the VHS mark: . There are four types of video cassettes: T-60, T-90, T-120, and T-160. The amount you can record on a tape is dependent upon the tape speed at which you record. The table below lists the recording time(hours:minutes) for each tape type according to recording speed. Tape Type T-60 T-90 T-120 T-160 SP Mode (Standard Play) 1:00 1:30 2:00 2:40 EP Mode (Extended Play) 3:00 4:30 6:00 8:00 Playing a video cassette If the video cassette has no safety tab(e. g. , a rented video cassette), the VCR will play the tape once you insert it. If the VCR does not play the video cassette, press PLAY. If you insert a video cassette without a safety tab into the VCR: · During the timer recording process, "TIMER" will blink on the display panel and the VCR will automatically eject the cassette. Searching forward while viewing a video cassette To search forward on a video cassette, press FF. The video cassette will advance rapidly and display a picture, but no sound. Press PLAY to return to normal play. Protecting video cassettes from accidental erasure Cassette have a safety tab to prevent erasure. Break off the safety tab with a screw driver. If you wish to record on a cassette without a safety tab, cover the hole with cellophane tape. Searching backward while viewing a video cassette To search backward on a video cassette, press REW. The video cassette will rewind rapidly and display a picture, but no sound. [. . . ] · Make sure the VCR is plugged in. Picture quality during playback is poor. · Adjust the picture quality by pressing ­CH/TRK+. Picture does not appear when you attempt to play a video cassette. [. . . ]