User manual DAEWOO DVQ-14H2FC

[. . . ] INSTRUCTION MANUAL TV/VCR COMBINATION DVQ 14H1FC DVQ 20H1FC DVQ 14H2FC DVQ 20H2FC CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To provide power to the TV, insert the AC plug into a standard 120V 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V 60Hz power. [. . . ] Ejecting a tape To remove a tape from the compartment, press the STOP/EJECT button on the front panel or on the remote control. The TV/VCR will eject the tape part-way. Grasp the cassette and remove the tape from the TV/VCR. 18 Chapter 4 : Operating Your VCR Playing a Tape 1. To begin playing a tape, place it in the TV/VCR's cassette compartment. If the erasure prevention tab has been removed, the tape will begin playing automatically. If the erasure prevention tab is intact, press the PLAY button on the front panel or on the remote control. To pause the tape and display a still frame, press the PAUSE/STILL button on the remote control. To stop the tape, press the STOP/EJECT button on the front panel or on the remote control. Searching for a scene If you are looking for a particular scene, you can use the FF and REW buttons to find the scene faster. Press the FF button during playback to search quickly in the forward direction. Press the FF button a second time to search at 7X normal(in SP speed) or 11X normal (in EP). Press the REW button during playback to search quickly in the reverse direction. Press the REW button a second time to search at 7X normal (in SP speed) or 11X normal (in EP. ) If you press FF or REW while the tape is stopped, the TV/VCR will quickly wind your tape in the selected direction. No picture from the tape will be displayed, but the tape moves at a much higher speed without the picture. Chapter 4 : Operating Your VCR 19 Tracking "Tracking" is a term that describes how the TV/VCR "locks on" to the signal recorded on the tape. If the TV/VCR is not tracking correctly, the picture during playback will be jumpy and distorted. Your TV/VCR is equipped with a sophisticated automatic tracking feature that can perfectly track a tape's signal without adjustment from the user. On some rare occasions, though, manual tracking may be required. Press and hold down the CH buttons on the remote control, one at a time. Adjust the tracking using these buttons until the picture is no longer distorted. Basic Recording Your TV/VCR makes it easy to record a program you are watching. Place the tape on which you want to record in the cassette compartment. Fast forward or rewind to the point where you want to begin recording. Press the SPEED button repeatedly to select the tape speed at which you want to record : SP or EP 4. The tape will start recording the channel you are watching, and also add an index mark. [. . . ] · Make sure the AIR/CABLE setting is correct. · The channel may not be programmed into memory. The picture rolls, slants, shows lines, is grainy, has poor color, or has ghosts. If the other station are OK, it may be a station problem. [. . . ]