User manual DAEWOO DWB-123CS

[. . . ] Avoid placing any obstacles near the inlet or outlet. - If the inlet or outlet is blocked with any obstacle, it may cause damage to the unit. - If you run or stop the unit more then 4-5 times an hour, it can cause damage to the unit. Wait at least 3 minutes before restarting the unit or in the case of power failure. [. . . ] Do not operate unit with front grille removed . · Be sure to use an exclusive power source. · Contact service man for replacement of power cord. 3 · HOW TO REMOVE THE FRONT GRILLE 1. Pull the Air-filter out of the Front Grille. Loosen screw which fasten Front Grille with driver. (when the knobs are too tight to release, leave them. ) ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; ;;;; ;;;;; 4. ­ Front Grille and chassis are fixed with snap-fit. ­ Push the right lower side of chassis to the left, with pushing left side of Front Grille to the right until the snap-fit is released. Push Push 2) Release left-lower snap-fit. ­ Push the left-lower side of chassis to the right, with pushing right side of Front Grille to the right until the snap-fit is released. Push Push 3) Pull lower side of the Front Grille until it is separated from the chassis. (when knobe remain, pull Front Grille until knobs are released from control) 4) Push base side of the Front Grille to upper side until it is separated from the chassis. 4 5. Reinstall the unit, side screws, front grille. CAUTION · When the front grille is reinstalled, the DOOR VENT should be in position first so that it would not be bent by grille. Door Vent 5 · HOW TO INSTALL THE DRAIN CAP Install the drain cap like Fig. There are two kinds of method to install the drain cap. The first method is that the shape of hole like It is good for the household. The second method is that the shape of hole is like It is good for the shop. The rear side of the unit SEAL DRAIN Drain Cap M4x8 SCREW: Use Screw(M4x8) only. · WINDOW INSTALLATION 1. The window where the Air Conditioner is to be installed should have enough strength to bear the weight of the Air Conditioner. Install the Mounting Angle at the Proper Location. Install the Air Conditioner using the Mounting Angle or other Hardware to be installed as shown in Fig. 1 For proper drainage, Rear side of the unit should be inclined about 5mm lower. Mounting Angle Close up the gap unit 5mm wall Fig. With 2 people, lift unit and insert it into the window opening. CAUTION : Two people must work together to avoid personal injury. Finish opening Close up the gap between unit and window using the sponge or tape for insulation as shown in Fig. 1 * If through the wall installation is required, you may choose to consult an independent servicing Dealer. 6 NAMES OF MAJOR COMPONENTS · DWA-122C / DWB-122C / DWB-123C / DWA-151C 9 3 10 7 11 4 3 7 4 2 8 2 8 1 5 6 1 5 6 · DWA-122CS / DWB-122CS / DWB-123CS / DWA-151CS 9 3 10 7 11 4 3 7 4 2 8 2 8 1 5 12 6 1 5 12 6 NO 1 2 3 4 5 6 PART NAME AIR FILTER GRILLE FRONT CABINET BLADE VERTICAL KNOB THERMOSTAT KNOB SELECTOR NO 7 8 9 10 11 12 PART NAME BLADE HORIZENTAL AIR VENT FRAME GUIDE TOP FRAME WINDOW KIT SHUTTER WINDOW AUTO LOUVER S/W (DWA-122CS/DWB-122CS/ DWB-123CS/DWA-151CS) 7 OPERATING INSTRUCTIONS NOTE · FOR MOST ECONOMICAL USE 1. [. . . ] · Check with dealer to determine proper unit capacity for application. · Stop noise by allowing water to drain from base fan through drain hole. · Place algaecide tablet in base pan · Remove water in base pan through drain hole. · Water in base pan is picked up by the fan blade and thrown onto the warm outdoor coil where water then evaporates. · Little or no cooling · Compressor lockout on initial plug in. [. . . ]