User manual DAEWOO DX-C811N

[. . . ] 8 channel DVR (Digital Video Recorder) Operating Instructions Model : DX-C811N S AFETY PRECAUTIONS @ @ ! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Precautions · Refer all work related to the installation of this product to qualified service personnel or system installers. [. . . ] 10 When the scheduled recording time is over, the REC indicator goes off and recording stops. 12 If you wish to stop recording while scheduled recording, press the [SCHEDULE] button, then the SCHEDULE indicator goes off and the Schedule Recording Mode is released. Schedule Recording Mode SCHEDULE G AL VL PL NOTE . . The recording time is set by 24H (00:00 - 23:59). You need to set 2 days if the setting is over one day. D/W ALL ALL START 18:01 00:00 18:01 END 23:59 08:59 08:59 MODE GROUP3 GROUP1 GROUP1 Digital Video Recorder The recording would not start when Ending time is ahead of Start time. Ex) ALL 22 M OTION DETECTED RECORDING (MOTION RECORD) Motion Detected Recording (MOTION RECORD) 1 Press the [MENU] button to go into the "MAIN MENU". 2 Press the [] button to move the cursor to the "RECORD SET". MAIN MENU DISPLAY SET RECORD SET RECORD GROUP SET ALARM RECORD SET SCHEDULE SET TIME/DATE SET SYSTEM SET NETWORK SET . . . 3 While the "RECORD SET" flashes, press the [] button or turn the [SHUTTLE ring] to the right to enter. MOVE SET EXIT 4 Press the [] button to move the cursor to the "MOTION DURATION". Then press the [] button to select a duration time ; 20 SEC 40 SEC 60 80 100 120 180 240 SEC 5 Press the [] button to move the cursor to the "CAMERA SELECT". Then press the [] button to select a motion detecting camera. RECORD SET RECORD GROUP AUDIO RECORD REPEAT RECORD PRE-RECORD MOTION DURATION CAMERA SELECT MOTION SENSITIV. GROUP1 NO YES YES 040SEC CAMERA1 LEVEL08 CANCEL OPERATION 6 Press the [] button to move the cursor to the "MOTION SENSITIV. ". Then press the [] button to select a sensitivity ; LEVEL1-Low sensitivity, LEVEL15-High sensitivity. MOVE oe SET 22 OK 33 11MO NOTE . . Motion sensitivity also varies upon on the number of blocks you select . 44 55 66MO 7 Press the [] button to move the cursor to the "MOTION AREA SET". 77 88MO 99 8 While the "MOTION AREA SET" flashes, press the [] button or turn the [SHUTTLE Ring] to the right to enter. Then motion blocks are appeared. 9 Select desired motion blocks by pressing numeric buttons. Digital Video Recorder 23 MOTION DETECTED RECORDING (MOTION RECORD) 10 Go to the "RECORD GROUP SET". 11 Press the channel button(s) you wish to activate `motion detected recording'. 12 Then, `M' is appeared next `F/S'. 13 To complete the setting and exit, press [MENU] button or [SHUTTLE HOLD] button. NOTE . . 1 REC LED on the front panel flashes on the standby mode of Motion recording. 2 There may be cases when the recorder's built-in motion detection function does not operate properly due to the condition of the input video signal or other factors. 3 It is recommended selection of at least 3 motion blocks to get more accurate motion recording. 4 Each channel starts motion recording separately with time interval upon on the motion detected. RECORD GROUP DEFINE GROUP PICTURE QUALITY CAMERA1 CAMERA2 CAMERA3 CAMERA4 CAMERA5 CAMERA6 CAMERA7 CAMERA8 . . . MOVE 1-8MO oe SET Motion Detected Recording MOTION G SET GROUP1 HIGH+ 30 F/M M 07 F/S ­ 07 F/S ­ 06 F/S ­ 06 F/S M 07 F/S ­ 06 F/S ­ 03 F/S ­ OK CANCEL 2 3 1 5 4 8 0031:13 0052G 6 7 THU 11:27:22 JUN. 05. 2003 Motion Detected channel flashes and turns to yellow color when it starts recording. 24 Digital Video Recorder T IME SEARCH ­ TIME AND DATE SEARCH TIME SEARCH ­ Time and Date Search NOTE . If an external USB HDD is connected to the DVR, choose which HDD you want to search on the SYSTEM SET menu. [. . . ] Live Record: Click to record the current live images. D PTZ Camera : PAN/TILE/ZOOM control button. F PLAYER: Local player; click to playback the images file downloaded from the DVR server. OSD ON/ OFF: OSD (On Screen Display on /off) E Camera Display buttons Multi View: Click to view in different view mode. HIGH: 720 x 486 MID: 360 x 243 LOW: 180 x 122 3 Status Bar A B SCHEDULE Recording ON/OFF status C Manual LOCK ON/OFF B C D A Current DVR Status (Time and Date, Power On / REC / PLAY / STOP / etc. . ) D Remain HDD capacity of internal storage and external storage 42 Digital Video Recorder CLIENT PROGRAM Image file down load from the DVR server 1 Click the "File Manager" button on the tool bar. [. . . ]