User manual DAEWOO G1680

[. . . ] WORTH knowing Please keep the video's guarantee sheet and receipt for your video in a safe place. Before you do anything with the video, please read the chapter "Setting up the video". Precautions x x x x x x Contents AUTO SET OP EJECT CH. x x Read this booklet carefully. Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. Read this page and the chapter and the "Setting up the video" to help you set up and adjust your video recorder. Do not put the video recorder in a hot or humid place (to avoid the risk of fire and electric shock). [. . . ] To prevent these problems adjust the V-HOLD knob on your television. NTSC : National Television Systems Committee. · This video can also play MESECAM (middle east secam not secam) cassettes. 12 13 Still There must be a cassette in the video. VCR CM Skip Still picture from playback. Each press of the button moves the picture on one frame. Press the play button to switch back to normal playback. If you press [CM Skip] button on the remote control during playback mode, tape advances for 30 seconds segment. After approximately five minutes on still, the cassette will automatically switch to normal playback. If the still picture is jumping, you can steady it by using the PR+ and PR- button. Auto Repeat If you press the PLAY button for 5secs during playback mode, REP should appear on your display, the video goes into Auto repeat mode. This video repeatedly plays the tape from beginning to end . To release this mode, press any mode operation button such as PLAY, FF, REW or STOP. Variable picture search VCR Keep pressing to vary the forward search speed. VCR - Keep pressing to vary the rewind search speed. Pressing the above buttons will vary the search speed in two speeds. Press to switch back to normal playback. Child lock You can only set the child lock with your remote control. Variable slow motion Press the button for about 5 seconds. VCR Starting from playback you can keep pressing control slow motion speed in six steps. Press to switch back to normal playback. to Finding new recordings (index scan) The video index search system allows you to find the beginning of any recording you have made on your video. Your video automatically records index marks on the tape whenever a recording is started. FF SP INDEX 01 No buttons of front panel can be operated now and LOCK INDICATOR ("SAFE") will be displayed momentarily on LED display. Keep your remote control in a safe place. To release child lock, press any button of the remote control. Press INDEX + or INDEX ­ to search forwards or backwards. The video will now wind to the beginning of a recording, play it for about 6 seconds, then wind on to the next one. 0:11:09 When you see the recording you want to watch, press PLAY. 14 15 OSD (On Screen Display) ON & OFF This VCR is set to "OSD (On Screen Display) ON" mode at the factory, but you can change it to OFF mode. When a function is changed at the front display or remote control the change will be displayed on the screen. Simple recording Load a cassette with its safety tab in place (see page 23). Press PR+ or PR- to choose the station you want to record. Press SP/LP if you wish to double the length of the cassette's recording time. For example, on an E-240 cassette you can record for up to four hours when SP is displayed, or up to eight hours when LP is displayed. MAIN MENU 1 TIMER PROGRAM PR PRESET VCR SETUP TAPE CONTROL PR+/-:SELECT OK:CONFIRM MENU:END Press MENU. Choose "VCR SETUP" And press OK. STOP SP PR01 ARD 2 * VCR SETUP CLOCK SET LANGUAGE SET RF OUTPUT SET 16:9 SET OSD ON/OFF PR+/-:SELECT OK:CONFIRM MENU:END Choose "OSD ON/OFF". VCR Press to start your recording. Press if you want to stop the recording for a short while. VCR Press to continue recording. 3 OSD ON/OFF ON OFF PR+/-:SELECT OK:CONFIRM MENU:END If you want OSD OFF mode, press PR- and press OK. OSD characters will not be displayed in the normal picture at the start of each mode change. VCR Press to stop your recording. These buttons are used on the following two pages. * Though the "16:9 SET" is displayed on the screen, this function is not available for this set. 16 17 x x For timer recordings, clock, date, and stations must be set correctly. Load a cassette with its safety tab in place (see page 23) and with enough free tape for the recording. Recording cassettes x x Normal timer recording Press MENU. Choose "Timer Program" by pressing OK. There are positions for eight timer programs. Press PR+ or PR- to select an unused program, for example `- - - -' then press OK to confirm. [. . . ] This means that the number has been adjusted in the past. The TV needs to be tuned in to get the blue auto set or auto search screen. (Refer to page 6) 29 Quick-start guide Please follow the guide from the beginning to the end. Before you connect the video equipment make sure all equipment is switched off at the plug. Stage 1. Connecting the video to your TV A Fit the batteries into the remote control. [. . . ]