User manual DAEWOO LM32L2BSM

[. . . ] 48586602E101-R0 LCD TELEVISION INSTRUCTION MANUAL LM32L1/LM32L1B1M LM32L2/LM32L2BSM LM32L2Z/LM32L2BZM LM32L2K/LM32L2BKM LM32L2R/LM32L2BRM LM37L1/LM37L1B1M LM37L2/LM37L2BSM LM37L2Z/LM37L2BZM LM37L2K/LM37L2BKM LM37L2R/LM37L2BRM LM42L1/LM42L1B1M LM42L2/LM42L2BSM LM42L2Z/LM42L2BZM LM42L2K/LM42L2BKM LM42L2R/LM42L2BRM Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. 2 Important Safeguards Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. [. . . ] · A tuning screen will appear and cursor will move from left to right / from right to left. If you want to stop tuning press the "MENU" button. · You should press the "OK" button to store program then the PR number is changed to red. If you don't want to store the program, press " " button to skip program. · To store another program, select other PR number using " " buttons and press " " buttons. PIP PR Manual Tuning OK Pr 01 Euro Access MENU Exit PIP PR IA Note : · If you are unable to get any programs using Auto Tuning because of a poor broadcasting signal, it is possible to store the Manual tuning. 30 Setting Up TV Stations Setup The Setup menu shows you information as follows: - Channel, System, Frequency, Station name, Program number and Store to PR number. 1. Searching for channels in the Setup menu · Press the " PR " buttons to select a program number you want. · Move to SETUP in the Install menu. · Search a real channel informations(Channel, System and Program) with " / " buttons. · If you save the selected channel to favourite program number, move the cursor to Store To and select using the " ", "OK" buttons. Fine tuning · Move to SETUP in the Install menu. · Move the cursor to Frequency by pressing " / " buttons. · Adjust the fine tuning with the " " buttons. Note : · If you are unable to get a good picture or sound because of a poor broadcasting signal, adjustment of the fine tuning might improve it. Picture Auto Tuning Manual Tuning Setup Access Access Access Access PR MUTE Screen Sound Install Function Edit Move Select MENU Exit PIP PR Picture Screen Sound Channel System Frequency Name Program C 22 Euro 479. 31 MHz ----00 00 OK Install Function Store To PIP PR Move Access 0~9 Adjust MENU Exit IA 3. Enter a station name · Move to SETUP in the Install menu. · Move the cursor to Name by pressing " buttons. · You can enter a station name with the " "buttons. " PIP PR Picture Screen Channel System Frequency C 22 Euro 479. 31 MHz ----00 00 " / " and Sound Name Program OK Install Function Store To ABCDEFGHIJKLMNO PQRSTUVWXYZ0123 4 5 6 7 8 9 - . = / + ", " ( ) Select MENU PIP PR Move Exit DI A Note : Only English is supported in this station name. 31 Setting Up TV Stations Edit The Edit menu shows you information as follows: - Program position assignment: Program number and Station name, Real channel number. - One can move on this edit mode directly using "Move"(Yellow) button on the remote control. PIP PR 1. · Move to EDIT in the Install menu. · Move the selection bar to the program number to delete with the " / " buttons. · Press the Delete (Red) button. Picture Screen Sound Edit Prog. [. . . ] If you want to look at a subpage for a longer period of time, press the "HOLD" button ( ). The HOLD symbol appears and the contents of the subpage shown are kept on the screen and no longer updated or switched to other subpages. Pressing the "HOLD" button again, the current subpage appears. CALLING UP SUBPAGE DIRECTLY Pressing the "S-CODE" button ( ) , " - - - - " appears. [. . . ]