User manual DAEWOO NRP-47CR

[. . . ] P/N:48586114E101-R0 INSTRUCTION MANUAL NRP-47CR PROJECTION MONITOR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. -2- IMPORTANT SAFEGUARDS Please read the following safeguards for your Monitor and retain for future reference. Always follow all warnings and instructions marked on the Monitor. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the Monitor. [. . . ] Timer lamp turns on in Off/On reservation. -13- Side and Rear Panel Side Panel It is convenient to use the input jacks provided at the side panel when connecting to the camcorder or video game. Back Panel -14- Parts of the remote controller -15- Method To Use Basic Menu Basic Menu - Basic menu appears on the screen if pressing the menu button of the remote control. - There are 5 items of Picture, Sound, Function, PIP and Special in the basic menu. If the desired item is selected, the relevant sub-items are displayed upward. Press the "Menu" button. · The main menu appears if pressing the Menu button. Press the " VOL¢ " button. · You may setup according to the directions on the screen after selecting the desired item and pressing the "¢ VOL¢º" button. · If the setup is completed, exit from the menu by pressing the "Menu" button. P I C T U R E Adjusts Brightness, Contrast, Sharpeness and Color(PAL & NTSC), Tint(NTSC Only). S O U N D Adjusts Balance and Equalizer. FUNCTION Adjusts Timer, Language and Picture NR. P I P Adjusts PIP S P E C I A L Adjusts Center, Convergence, Dolby Virtual, Component -16- To Watch Monitor To Watch Monitor - Buttons with same name in the main body performs same function. Press the "Main Power" button of the main body. ·The buttons of the remote control and the main body operate only when pressing the "Main Power" button of the main body. The remote control and the main body do not operate if turning the "Main Power" button of the main body off. VIDEO COMPONENT POWER To suddenly turn sound off 1. No sound is heard if `Mute' is displayed on the screen. Sound is heard again if pressing the `Mute' button once again. For example, please use this button when telephone rings or when guest comes while watching Monitor. SCREEN SCREEN DOLBY SOUND SIZE VIRTUAL MODE MODE MENU RECALL SLEEP VOL VOL MUTE PIP POSITION SWAP PIP VIDEO STILL -17- Press the "Main Power" button. · Press the "Main Power" button of the main body. · The stand by lamp turns on in red color. · Press the "Power" button of the main body or the "Power" button of the remote control. · The stand by lamp turns on in "green" color and the Monitor turns on. Adjust volume. ·Sound reduces if pressing the ¢¸ VOL button. · Sound increases if pressing the VOL¢º button. Vo l 9 Press the "Power" button for turning the Monitor off. · Monitor turns off and the stand by lamp changes to red color. -18- Selection of Input Signal When watching video, Camcorder, Cable Monitor - See 9p for connection method of Monitor and "Video". Press the "VIDEO" button. · Screen changes as follows whenever pressing the "VIDEO" button. Video 1 Video 2 Video 3 Video 3 Notices: Cautions in menu setup · Menu disappears if not operating any button for 10 seconds from the menu. · Don't connect video signal and S-video signal to the video input terminal (1, 2, 3) at the same time. If connecting both signals at the same time, the Svideo operates. · You can watch only when this input terminal must be connected to the composite video (generally video) signal. · If sound signal is of mono method, connect it to the L-terminal of the sound input terminal. -19- When watching DTV and DVD (component input) - See 11p, 12p for connection method of DTV and DVD (component input). - Input component video (called as color difference signal) as DVD signal. Press the "COMPONENT" button. · The screen changes whenever pressing the button once. Video 1 Component 2 Component 1 Component 2 Component 1 -20- Method of changing the component Input selection through Menu button Press the Menu button. · Press the "¢ VOL¢º" button until the "°, " mark will come on the "Special". · Press the "°, , " button in the "°, " mark will come on the "Special" VOL VOL Select "Component 1" or "2" from the "Special". · Component Off is repeated whenever pressing the "VOL¢º" button. · Component 1 is repeated whenever pressing the "VOL¢º" button. · Component 2 is repeated whenever pressing the "VOL¢º" button. VOL VOL -21- Screen Adjustment When setting up various screen mode - The user may select various pictures setting in accordance with the environmental light. Press the "Screen Mode" button. · The screen adjustment status changes as following screens are displayed sequentially whenever pressing the button of the Screen mode. · Screen automatically changes to the User Screen if adjusting Brightness, Contrast, Sharpness, Color from individual screen mode. · When turning the unit ON, it will return to the picture mode previously selected. User Standard Dynamic Cinema -22- When removing screen noise - Screen noise (snowy noise) will become visible when broadcasting signals are weak. Press the "Menu" button. · Press the "¢ VOL¢º" button until the "°, " mark will come on the "Picture". [. . . ] - Adjust sleep time with sleep reservation button of a remote control. Press the "SLEEP" button. · Sleep Off ¡æSleep 10 ¡æSleep 20 ¡æSleep 30 ¡æ Sleep 60 ¡æSleep 90 ¡æSleep Off is repeated whenever pressing the "Sleep" button. · Stop to pressing at the desired time. · Sleep Off means status that "Sleep" is not setup. -34- Adjustment of static convergence Adjustment of static convergence - After you do the adjustment of this title, please ensure that table of contents at page 8 is also changed. - Perform this adjustment when color looks separated or when focus is not suitable or when the screen looks spread, after movement to another place or watching projection Monitor for a long time. Press the "Menu" button. · The Menu screen appears as in the right. Select "Special". VOL VOL · Select "Special" with the "¢ VOL¢º" button. [. . . ]