User manual DAEWOO RCU-300

[. . . ] - Insert the body end of HOSE AS in the hose hole Body end of the cleaner. - Caution : Insert the protrusion of HOSE end through "" mark in side of the hole when connected the HOSE(body end) and the BODY, The HOSE can not be removed from the BODY. If you need to disassemble it, call the A/S center. HOSE AS HEAD end Hose Guide HANDLE ASSEMBLING · HANDLE assembling. - Insert HANDLE in the handle hole on the top of the Body as below the picture. [. . . ] · Grasp the DUST BOX LEVER and pull out the DUST BOX from BODY. · Pull out the EXHAUST FILTER EXHAUST FILTER BODY DUST BOX Dust Box Lever EMPTY DUST BOX · When dust reaches the "FULL" line in the DUST BOX or FILTER WARNING LAMP light. · Push the DUST REMOVAL BUTTON and the dust will drop out. - FULL Dust Removal Button - FULL 6 RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 8 INNER FILTER CLEANING AND REPLACING · Lift up the DUST BOX COVER and rotate and remove the INNER FILTER · Tapping it to remove the dust from the pleats as below in the picture. - Caution : This INNER FILTER is not washable. After tapping it, reassemble it and use the cleaner. When tapping, be careful not to damage the filter. Replace the new INNER FILTER in every a year. Dust Box Cover Inlet Filter EXHAUST FILTER CLEANING AND REPLACING · Disassemble the EXHAUST FILTER. (See 6 page) · If the EXHAUST FILTER become dirty. - Caution : This INNER FILTER is not washable. Filter Frame Clean Filter CLEAN FILTER 7 RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 9 REPLACING BELT & HEAD LIGHT REPLACING BELT OF AGITATOR BRUSH · Turn OFF the cleaner. · Remove the BOTTOM PLATE of the HEAD. (unscrewing 5 screws with "+" shape screw driver) · Set the new BELT over Motor Pully. · Slip the AGITATOR BRUSH into the BELT and reassemble. · Replace the BOTTOM PLATE and secure the 5 screws. Check the cleaner is unplugged from the electrical socket. REPLACING HEAD LIGHT ( ONLY FOR RCU-3008 SERIES ) · Turn OFF the cleaner. · Press the RELEASE PEDAL and place the HANDLE in the low position. (unscrewing a screw with "+" shape screw driver) · Pull the BULB straight out of the SOCKET. · Replace the LENSE and secure a screw. Lense Head Light 8 RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 10 PRECAUSIONS FOR SAFE USE This vacuum cleaner should only be used for normal dry household dust and dirt. The manufacturer cannot be held responsible for any damage caused by use or operation of the cleaner contrary to these instructions. If the cleaner is wrongly operated for a purpose other than that for which it is intended, no liability can be accepted for any possible damage. · Do not vacuum areas which contain moisture or water and inflammable matter, needles, pins, razor blades, matches, cigaretteends, etc. , since they may damage the cleaner or dust bag or cause a fire. · When rewinding the power cord, hold the plug body before pressing the cord rewind button to prevent whipping. · Do not pull the power cord out beyond the specified length. · Make sure the Filters always inserted. · This product provided with a cable which, if damaged, must be replaced by a repair shop authorized by the manufacturer since special tools are required. 9 POW DER RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 11 TROUBLE SHOOTING Please check each item below if you have trouble with your cleaner. Before checking, ensure that the cleaner is unplugged from the power supply. [. . . ] Inner Filter is blocked. Cleaner or Tool won't pick up dirt. Cleaner is difficult to push Visible dust escaping from cleaner. 1. Filter missing or installed incorrectly. Dust Box installed incorrectly. 10 RCU-3008F/RCU-3006F DESUK 1/25/06 9:12 PM Page 12 Disposal of Used Electrical & Electronic Equipment. The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste. [. . . ]