User manual DAEWOO SL800

[. . . ] 960-Hour Time Lapse Video Cassette Recorder User's Guide SL800 15540 Herriman Blvd. - Noblesville, IN 46060 1-800-774-0284 www. spycorder. com Be sure to read carefully and follow all the SAFETY INFORMATION on pages i, ii, iii. Keep the manual in a safe place for future reference. Safety information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. [. . . ] · If a recording pause continues for 5 minutes or more, the VCR will go into stop mode to avoid damage to the tape. Recording can be interrupted temporarily. 1 Press the PAUSE/STILL button during recording. · The "REC" and " display panel. " indicators are displayed on the 8 Press the SET - (or +) button to set the recording stop hour(eg : 06), then press the SHIFT button. · The cursor is moved to the recording stop minutes position. 2 To resume recording, press the REC button, or press the PAUSE/STILL button again. 960-Hour Time Lapse Video Cassette Recorder 960-Hour Time Lapse Video Cassette Recorder 15 14 9 · If the set stop time is earlier than or the same time as the set start time, the VCR will consider the stop time to be the following day. Press the SET - (or +) button to set the recording stop minutes(eg : 00), then press the SHIFT button. 10 Press the SET - (or +) button to select the recording speed(eg : 24), then press the SHIFT button. · The cursor is moved to the N/Y position. Example 2 : To record on everyday from 10 : 00 to 18 : 00, in 24-hour mode (recording speed) 1 2 Repeat steps 1 to 3. Press the SHIFT button, until the cursor is on "DLY". The MENU below is displayed. 11 Press the SET - (or +) button to select "Y". recording will not take place Programmed timer recording Example 1 3 Repeat steps 5 to 13. Programmed timer recording Example 2 · Repeat steps 4 to 11 to program timer recordings for other days of the week. · To set two or more timer recordings the same day of the week, press the SHIFT button, until the cursor is located in the day of the week for the second recording, then press the SET - (or +) button, to set the desired day of the week. With each press of the SET - ( or +) button, the day will change as indicated below. Changing a Program Timer Recording 1 Press the MENU, SHIFT , SHIFT , SHIFT buttons in sequence to display the TIMER PROGRAM SET(1) menu. Press the SHIFT (or ) button, until the cursor is located in the setting to correct. Press the SET - (or +) button, to correct the setting. · Press the MENU button three times until the normal screen is displayed. SET - : direction , SET + : direction 2 3 · To modify, cancel timer recording, press the POWER/TIMER button to cancel the timer recording mode. 12 Press the MENU button three times, the normal screen is displayed. 13 Press the POWER/TIMER button. · The timer recording indicator " " will light on the display panel. The VCR is now in timer recording stand-by mode. 4 Press the POWER/TIMER button. 16 960-Hour Time Lapse Video Cassette Recorder 960-Hour Time Lapse Video Cassette Recorder 17 To Cancel a Program Timer Recording 1 2 Repeat step 1 above. Press the SHIFT (or ) button until the cursor is located in the "Y" corresponding to the timer recording to cancel. Press the SET - (or +) button, to select "N". Press the MENU button three times until the normal screen is displayed. Press the POWER/TIMER button. · The clear button can erase the programmed timer recording in the line that the cursor is located. Alarm Recording Alarm Recording Setting Alarm recording is performed when there is an input (trigger) at the ALARM IN terminal, " " is displayed on the display panel. 2 Press the MENU, SHIFT , SHIFT buttons in sequence to display the REC MODE SET menu . 3 Press the SHIFT button until the arrow mark ( ) points to Alarm Rec Set. 4 Press the SHIFT button to display the ALARM REC SET menu. 3 4 5 Notes. . . · During timer recording all the buttons on the VCR, except the STOP button, are disabled. [. . . ] The video heads should be cleaned and inspected every 1, 000 hours. The video heads usage can be checked using initial menu, running time. - Load a cassette tape with erasure prevention tab or cover the tab hole with adhesive tape. - Be sure to select "YES" for autorepeat recording. - Set "YES" again for autorepeat recording. · Press the RESET button for more than 5 seconds to perform the reset. [. . . ]