User manual DAEWOO ST737

[. . . ] WORTH knowing Please keep the video's guarantee sheet and receipt for your video in a safe place. Precautions x x x x x x AUTO SET OP EJECT CH. x x Read this booklet carefully. Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. Read this page and the chapter and the "Setting up your video" to help you set up and adjust your video recorder. Do not put the video recorder in a hot or humid place (to avoid the risk of fire and electric shock). [. . . ] Choose `VCR SET UP' by pressing PR- twice, then OK. Once the `CLOCK SET' display is on the screen, move to the position you want to change by pressing or . Use the number buttons 0 to 9 on the remote control to enter the correct time and date. Press OK to confirm the settings, and press MENU to end. CLOCK SET 2 TIME 11:41 DATE 12/05/2003(MON) 0-9:SETUP (HOUR) / :CORRECT OK:CONFIRM MENU:END 17 Recording cassettes x x If you want to use the video's timer to record a programme, the clock, date and stations must be set correctly. Load a cassette with its safety tab in place (see page 24) and with enough free tape for the recording. Simple recording Load a cassette with its safety tab in place (see page 24). STOP PROG SP PR01 ARD STEREO ON 1 4 2 5 3 6 TV/VCR AV A Press PR+ or PR- to choose the station you want to record. Press SP/LP if you wish to double the length of the cassette's recording time. For example, on an E-240 cassette you can record for up to four hours when SP is displayed, or up to eight hours when LP is displayed. 7 8 9 30 0 VCR EJECT Press to start your recording. SP/LP PAL/SEC INDEX PR MENU Press if you want to stop the recording for a short while. VCR PR A. SEL Press VCR to continue recording. to stop your recording. Press One-touch recording-OTR These buttons are used on the following two pages. VCR Press PR+ or PR- to choose the station you want to record. Every time you press , the recording time will increase by 30 minutes. It is possible to record for up to 10 hours if there is enough room on the cassette. · To cancel OTR press and hold the STOP button for about five seconds until the video stops recording. · If you want to record from other equipment that is connected to your video, see pages 3, 4 and 9. 18 Timer recording using ShowView ShowView is an automatic system which makes it easier to set the timer. 1 SHOWVIEW 83077---0-9:SHOWVIEW NUMBER :CORRECT OK:CONFIRM MENU:END Press PROG. (If ShowView mode does not appear on the screen, it is not available on your video. ShowView numbers are shown in TV guides. From your current TV guide, type in the number next to the programme you want to record using the number buttons 0-9. Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. If you wish to change any details: Move to the details you want to change using the / buttons. Change the setting using the PR+ or PR- or number buttons 0-9. 2 HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM? ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN) PR+/-:SELECT OK:CONFIRM MENU:END 3 PR 03 START TIME 21:20 END TIME 22:20 START DATE 14/05(WED) TAPE SPEED SP VPS/PDC ON PR+/-:SELECT (AV1/AV2) 0-9 : SETUP (PR) / :CORRECT OK:CONFIRM MENU:END TIMER PROGRAM (ONCE) If all the settings are correct, press OK. The on screen display will remind you to enter a cassette and turn the video off. Press to switch your video off. Your video will not record unless you do this. You can switch the video on again if you want to set the timer to record another programme. Remember to switch the video off when you have finished setting the timer. 4 If VPS/PDC does not appear on the screen, it is not available on your video. VPS=Video Programming System PDC= Programme Delivery Control. · VPS/PDC sets your video to adjust the start times of your timed recording. This happens even if a programme starts earlier or later than advertised. [. . . ] (Refer to page 5) 29 Quick-start guide Please follow the guide from the beginning to the end. Before you connect the video equipment make sure all equipment is switched off at the plug. Stage 1. Connecting the video to your TV A Fit the batteries into the remote control. Make sure that the (+) and (-) marks on the batteries agree with the (+) and () marks inside the battery compartment. [. . . ]