User manual DAEWOO SV-250E

[. . . ] WORTH knowing Please keep the video's guarantee sheet and receipt for your video in a safe place. Before you do anything with the video, please read the chapter "Setting up the video". Precautions x Read this booklet carefully. x Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. x Read this page and the chapter and the "Setting up your video" to help you set up and adjust your video recorder. x Do not put the video recorder in a hot or humid place (to avoid the risk of fire and electric shock). [. . . ] Choose "VCR SETUP" And press OK. Press PR+ or PR- to choose the station you want to record. Press SP/LP if you wish to double the length of the cassette's recording time. For example, on an E-240 cassette you can record for up to four hours when SP is displayed, or up to eight hours when LP is displayed. 2 VCR SETUP CLOCK SET LANGUAGE SET RF OUTPUT SET 16:9 SET OSD ON/OFF PR+/-:SELECT OK:CONFIRM MENU:END VCR Choose "OSD ON/OFF". Press to start your recording. Press if you want to stop the recording for a short while. VCR Press to continue recording. to stop your recording. 3 OSD ON/OFF ON OFF If you want OSD OFF mode, press PR- and press OK. MENU:END VCR Press PR+/-:SELECT OK:CONFIRM OSD characters will not be displayed in the normal picture at the start of each mode change. These buttons are used on the following two pages. One-touch recording-OTR VCR Press PR+ or PR- to choose the station you want to record. Every time you press , the recording time will increase by 30 minutes. It is possible to record for up to 10 hours if there is enough room on the cassette. · To cancel OTR press and hold the STOP button for about five seconds until the video stops recording. · If you want to record from other equipment that is connected to your video, see pages 3, 4, 5 and 9. 18 19 Timer recording using ShowView ShowView is an automatic system which makes it easier to set the timer. x x For timer recordings, clock, date, and stations must be set correctly. Load a cassette with its safety tab in place (see page 25) and with enough free tape for the recording. 1 SHOWVIEW 83077---0-9:SHOWVIEW NUMBER :CORRECT OK:CONFIRM MENU:END Press PROG. (If ShowView mode does not appear on the screen, it is not available on your video. ShowView numbers are shown in TV guides. From your current TV guide, type in the number next to the programme you want to record using the number buttons 0-9. Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. If you wish to change any details: Move to the details you want to change using the / buttons. Change the setting using the PR+ or PR- or number buttons 0-9. If all the settings are correct, press OK. The on screen display will remind you to enter a cassette and turn the video off. Your video will not record unless you do this. You can switch the video on again if you want to set the timer to record another programme. Remember to switch the video off when you have finished setting the timer. Normal timer recording Press MENU. Choose "Timer Program" by pressing OK. There are positions for eight timer programs. Press PR+ or PR- to select an unused program, for example `- - - -' then press OK to confirm. Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. Press OK to confirm. x TIMER PROGRAM (ONCE) PR -START TIME --:-END TIME --:-START DATE --/-TAPE SPEED SP VPS/PDC OFF PR+/-:SELECT (AV1/AV2) 0-9 :SETUP(PR) / :CORRECT MENU:END 1 HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM? ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN) 2 HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM? ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN) PR+/-:SELECT OK:CONFIRM MENU:END PR+/-:SELECT OK:CONFIRM MENU:END 3 PR 03 START TIME 21:20 END TIME 22:20 START DATE 16/10(SAT) TAPE SPEED SP VPS/PDC ON PR+/-:SELECT (AV) 0-9 : SETUP (PR) / :CORRECT OK:CONFIRM MENU:END TIMER PROGRAM (ONCE) 2 x x x x x 4 If VPS/PDC does not appear on the screen, it is not available on your video. VPS=Video Programming System PDC= Programme Delivery Control. [. . . ] Before you connect the video equipment make sure all equipment is switched off at the plug. Stage 1. Connecting the video to your TV A Fit the batteries into the remote control. Make sure that the (+) and (-) marks on the batteries agree with the (+) and (-) marks inside the battery compartment. B Plug your aerial into the ANT IN socket of the video. [. . . ]