User manual DAEWOO SV294

[. . . ] DF-L72G1N-LS(GB) 04. 7. 1 3:21 AM 1 Important Safeguards INTRODUCTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated `dangerous voltage` within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION POUR VITER LES CHOC LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 CLASSE 1 LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT PRODUIT LASER NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer's attention to Article 820-40 of the National Electric Code (U. S. A. ). [. . . ] You can change the TV audio using the [AUDIO] button. Press [AUDIO] repeatedly to change the TV audio, according to the Broadcast audio signal as shown below. STEREO+SAP Audio Signal Stereo Mono (No display) SAP Stereo STEREO Audio Signal Stereo Mono (No display) Stereo SAP Audio Signal Mono SAP Mono MONO Audio Signal Mono (No display) The current audio channel is displayed on-screen. If SAP is selected, but there is no SAP channel being broadcast, you will still hear the main audio channel. If the sound is poor quality when set to Stereo, you can often improve it by changing to Mono. When an external input is selected, the audio channel can be switched only to Stereo. OSD Menu Options for DVD During DVD playback, press [DISPLAY] to show information about the current disc. While the disc information is displayed, press [DISPLAY] again to show the disc remaining time. Title Shows the current title number and total number of titles, and skips to the desired title number. 1 2 3 4 Press [DISPLAY] during playback. The on-screen display appears on the TV screen. Use [. . . ] to select the `Title` icon on the on-screen display. Press [ENTER] to confirm. 36 On-Screen Display Overview Chapter Shows the current chapter number and total number of chapters, and skips to the desired chapter number. 1 2 3 4 Press [DISPLAY] during playback. The on-screen display appears on the TV screen. Use [. . . ] to select the `Chapter` icon on the on-screen display. Press [ENTER] to confirm. Angle Shows the current angle number and total number of angles, and changes the angle number. 1 2 3 4 Press [DISPLAY] during playback. The on-screen display appears on the TV screen. Use [. . . ] to select the `Angle` icon on the on-screen display. SETUP Audio Shows the current audio soundtrack language, encoding method, and channel number, and changes the setting. 1 2 3 4 Press [DISPLAY] during playback. The on-screen display appears on the TV screen. Use [. . . ] to select the `Audio` icon on the on-screen display. Press [ENTER] to confirm. Subtitle Shows the current subtitle language, and changes the setting. 1 2 3 4 Press [DISPLAY] during playback. The on-screen display appears on the TV screen. Use [. . . ] to select the `Subtitle` icon on the on-screen display. Press [ENTER] to confirm. Elapsed Shows the elapsed playing time, and skips to the desired time. 1 2 3 4 Press [DISPLAY] during playback. The on-screen display appears on the TV screen. [. . . ] DVD Recorder+VCR A/V Out jacks are not connected to TV A/V In jacks. DVD Recorder+VCR Audio/Video Out is not selected for viewing at the TV. DVD Recorder+VCR's TV audio channel is set to SAP or MONO. The remote control is not pointed at Remote control does not the remote sensor of the DVD work properly. [. . . ]