User manual DAEWOO SY20C6144-A

[. . . ] Owner's Manual Be sure to read carefully and follow all the SAFETY INFORMATION on pages i-iii. Keep the manual in a safe place for future reference. 1280 HOUR TIME LAPSE RECORDER - 40 HOUR REAL TIME 14" COMBO 20" COMBO Model : SY20C6144-A P/N: 97P95600N0-79 PRODUCT INFORMATION Safety information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. [. . . ] Any mode Quad mode Single mode C1 C3 C2 C4 C2 Auto Sequence mode Single mode DISPLAY EJECT A00/002H EJECT A00/002H QUAD Mode C1 01/01/2003 WED 12:30:00 Picture In Picture(PIP) Mode C1 01/01/2003 WED 12:30:00 PIP mode** **It converts into 2 channel PIP mode. PIP mode C2 Auto PIP Sequence mode EJECT A00/002H EJECT A00/002H Quad Mode Operation 01/01/2003 WED 12:30:00 Sequence Picture In Picture Mode (Sequence PIP) Auto Sequence Mode C1 · To playback in still mode, press the FREEZE button in Freeze mode of VCR playback signal. · No signal parts and Boundary line are displayed at back side in zoom scan mode. Connect the cameras to the monitor. The monitor is defaulted to the quad setting. Zoom mode operation This mode enlarges and scans the camera signal. By pressing C1, C2, C3, C4 on the front panel, the subject moves to upper, bottom, left or right side and is scanned. EJECT A00/002H Sequential Auto Mode Operation Single Mode Press the AUTO button, it should display one camera after another. · The DWELL time can be adjusted from 1 to 30 seconds in the INDIVIDUAL SET of the MONITOR SET screen. · You can hear the audio only when the audio is turned on. · Adjustment channel could be interfered in blueback screen. 12 " " mark in Quad mode screen indicates current output audio channel. To select it, press Audio Sel button. Automatic Camera Skip in the Auto mode If you do not wish to view a particular camera, set the DWELL in the INDIVIDUAL SET mode of the MONITOR SET to a value of OFF. 13 Monitor Mode Set Clock Setting 1 2 Turn the power on to all devices used. Press the MENU button, the initial MENU is displayed. mark is located in "Monitor Mode Set". MENU Monitor Mode Set VCR Mode Set Terminal Output Set Buzzer Set YES Alarm Time Power Loss Time Default Load NO shift: sel: end:MENU Monitor Mode Set Setting the On-Screen Display You can select the display of the ALARM TIME, DATE/TIME, TITLE, TAPE MODE, ALARM COUNTER, TAPE COUNTER, BLANK COLOR and BOUNDARY LINE. 1 Turn the power on to all devices used. 2 Press the MENU button, the initial MENU is displayed. mark is located in "Monitor Mode Set". MENU Monitor Mode Set VCR Mode Set Terminal Output Set Buzzer Set YES Alarm Time Power Loss Time Default Load NO shift: sel: end:MENU DISPLAY 3 Press the SHIFT button, the MONITOR MODE SET menu is displayed. MONITOR MODE SET Clock Set Screen Display Set Individual Set Motion Set Picture Set shift: sel: end:MENU · ALARM TIME is the duration time that the audible buzzer sounds. ALARM TIME can be adjusted from 1 to 60 seconds in Screen Display Set mode. · TITLE : A maximum of 8 characters (letters, numbers or spaces) can be used in title mode. · BOUNDARY LINE: you can turn ON or OFF of boundary line for being visible. · BLANK COLOR: you can select BLUE, GRAY or BLACK using the SET ­/+ button will decide the color of the blank channel. 3 Press the SHIFT button, the MONITOR MODE SET menu is displayed. MONITOR MODE SET Clock Set Screen Display Set Individual Set Motion Set Picture Set shift: sel: end:MENU 4 Press the SHIFT displayed. button, the CLOCK SET menu is CLOCK SET Date Format: MON/DAY/YR 13:50:00 (HR:MIN:SEC) Thu03/13/03 (MON/DAY/YR) 4 Press the SHIFT button until mark is located in "Screen Display Set". SCREEN DISPLAY SET Alarm Time : 03Sec Date/Time : Yes Title : Yes Tape Mode : Yes Alarm Counter : Yes Tape Counter : Yes Boundary Line : Yes Black Color : BLUE shift: sel: end:MENU shift: sel:+­ end:MENU 5 6 7 Press the SET ­ (or +) button to set the hours/minutes and seconds. Press the SET ­ (or +) button to set the month/day and year. Then, press the SHIFT button. · The day of the week is set automatically. 5 6 10 Press the MENU button until the normal screen is displayed. · The setting procedure is now complete. 14 Press the SHIFT button, the SCREEN DISPLAY SET menu is displayed Press the SET ­ (or +) button to set the modes you want. - Alarm functions Connect the alarm devices such as PIR sensors or 15 Monitor Mode Set Monitor Mode Set · Alarm sensor can be released by pressing MENU button for 2 seconds. magnetic reed switch, etc. to the sensor port on the back of the cameras or monitor. An audible buzzer for 1 to 60 seconds and an alarm output for 1 to 60 seconds are provided to alert the user or to activate a recorder. The trigger signal is sent to the monitor when an alarm is activated. The picture will be displayed in full screen, even if the monitor is set to quad mode. When the next alarm is activated after the first alarm hold time, each alarm input picture will be displayed sequentially in full screen and returns to quad mode. [. . . ] - The unit is not set to timer recording - Press the TIMER button to lit on TIMER stand-by mode. - "N" is selected for the TIMER - Be sure to select "Y" for the TIMER PROGRAM REC SET. PROGRAM SET. THE OTHERS 40 41 Troubleshooting Guide Specifications POSSIBLE CAUSE CORRECTIVE ACTION - Be sure to select "YES" for alarm recording. - Adjust it by using the manual tracking. [. . . ]