User manual DAEWOO T-7

[. . . ] INSTRUCTION MANUAL Video recorder For model number, see the front display of your video UK lish Eng The following standard functions are available on this set. NTSC playback See page 13 MESECAM tape playback See page 13 Index scan See page 14 Wide-screen format See page 15 Commercial skip See page 15 High-speed rewind See back cover for quick-start guide Helpline number: 0870 100 2525 With queries, please quote the page number, reference number and model number. WORTH knowing Please keep the video's guarantee sheet (pages 27 and 28) and receipt for your video in a safe place. Precautions x x x x x x x AUTO SET OP EJECT CH. x x x Read this booklet carefully. Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. Read this page and the chapter "Setting up your video" to help you set up and adjust your video recorder. Do not put the video recorder in a hot or humid place (to avoid the risk of fire and electric shock). [. . . ] If you wish to change any details: Move to the details you want to change using the / buttons. Change the setting using the PR+ or PR- or number buttons 0-9. If all the settings are correct, press OK. The on screen display will remind you to enter a cassette and turn the video off. Your video will not record unless you do this. You can switch the video on again if you want to set the timer to record another programme. Remember to switch the video off when you have finished setting the timer. 2 HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM? ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN) PR+/-:SELECT OK:CONFIRM MENU:END 3 PR 03 START TIME 21:20 END TIME 22:20 START DATE 21/08(SAT) TAPE SPEED SP PDC ON PR+/-:SELECT (AV) 0-9 : SETUP (PR) / :CORRECT OK:CONFIRM MENU:END TIMER PROGRAM (ONCE) 4 If PDC does not appear on the screen, it is not available on your video. · PDC sets your video to adjust the start times of your timed recording. This happens even if a programme starts earlier or later than advertised. PDC works when the broadcaster sends a signal, but the signal is not always sent. If you are not sure the signal will be sent, it is best to switch PDC off. · · · · · 18 If there is no programme number displayed under `PR' in the change menu, the video doesn't yet know the number for the programme you want. Type it in and this will be stored for later recordings. If you wish to record from a satellite receiver, select under `PR' the satellite programme or AV (depending whether the video is connected with the antenna cable or the scart-cable). Leave the satellite tuner switched on and set the programme you want to record. The video will warn you if you have set the timer to start recording a second programme before the first recording has finished. To stop the recording after it has already started, press and hold the STOP button for about five seconds until the video stops recording. VideoPlus+ and Plus code are trademarks of Gemstar Development Corporation. VideoPlus+ system is manufactured under license from Gemstar Development Corporation. x x For timer recordings, clock, date, and stations must be set correctly. Load a cassette with its safety tab in place (see page 23) and with enough free tape for the recording. Normal timer recording Press MENU. Choose "Timer Program" by pressing OK. There are positions for eight timer programs. Press PR+ or PR- to select an unused program, for example `- - - -' then press OK to confirm. Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. [. . . ] If the TV/VCR button on the video remote control does not work, read the instruction book for the TV to find out about an audio video button. The video has a number other than 52 when RF appears A number other than 52 might be displayed on the video when RF is flashing in the display. This means that the number has been adjusted in the past. The TV needs to be tuned in to get the blue auto set or auto search screen. Refer to page 5. 29 Quick-start guide Please follow the guide from the beginning to the end. Before you connect the video equipment make sure all equipment is switched off at the plug. Stage 1. [. . . ]