User manual DAEWOO VP2600S

[. . . ] This product is designed to be used in the home. Anything other than household use or similar general use in line with these instructions may be dangerous and may mean the guarantee is not valid. Contacts Missing items If anything is missing from the product you have bought or you need to replace the instructions or the remote control, contact your Comet store. The phone number is on your Comet sales receipt. · · Service and repair You should take small products to your Comet service centre, or if this is inconvenient, to any Comet store. [. . . ] To stop the recording after it has already started, press and hold the STOP button for about five seconds until the video stops recording. VideoPlus + and Plus code are trademarks of Gemstar Development Corporation. VideoPlus + system is manufactured under license from Gemstar Development Corporation. 19 x x For timer recordings, clock, date, and stations must be set correctly. Load a cassette with its safety tab in place (see page 23) and with enough free tape for the recording. Normal timer recording HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM? ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN) 1 PR+/-:SELECT OK:CONFIRM MENU:END SV/V+ 1 4 2 5 3 6 TV/VCR AV A Press MENU. Choose "Timer Program" by pressing OK. Press PR+ or PR- to select an unused channel, for example `- - - -' then press OK to confirm. There are positions for eight timer programs. Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. Press OK to confirm. x 7 8 9 30 0 2 EJECT TIMER PROGRAM (ONCE) PR -START TIME --:-END TIME --:-START DATE --/-TAPE SPEED SP PDC OFF PR+/-:SELECT (AV) 0-9 :SETUP(PR) / :CORRECT MENU:END x x x x x SP/LP PAL/SEC INDEX PR MENU PR A. SEL PR : Use PR+ if you want to choose the AV channel or 0 to 9 for other channels. Start time : Use buttons 0 to 9 to enter the start time. End time : Use buttons 0 to 9 to enter the end time. Start date : Use buttons 0 to 9 to enter the date. Tape Speed : Use PR+ if you want to choose LP (see page 18). PDC : Use PR+ if you want to switch PDC on (see page 19). If PDC does not appear on the screen, it is not available on your video. 3 PR START TIME END TIME START DATE TAPE SPEED PDC PR+/-:SELECT (AV) 0-9 : SETUP (PR) / :CORRECT OK:CONFIRM TIMER PROGRAM (ONCE) 01 18:10 20:30 16/03(FRI) LP ON MENU:END If you want to change any of the details. Move to the details you want to change using the and buttons. Change the setting using the PR+ or PR- or number buttons 0 to 9. These buttons are used on the following two pages. 4 5 TMR If all the settings are correct, press OK to confirm. The on screen display will remind you to enter a cassette and turn the VCR off. Switch your video off by pressing the button. You can switch your video on again if you want to set the timer to record another programme. Remember to switch the video off when you have finished. · The video will warn you if you have set the timer to start recording a second programme before the first programme has finished. If you don't adjust the times, the video will record the first programme completely, then start to record the second one. [. . . ] Before you connect the video equipment make sure all equipment is switched off at the plug. Connecting the video to your TV A Fit the batteries we have provided into the remote control. Make sure that the (+) and (-) marks on the batteries agree with the (+) and (-) marks inside the AC 230V 50Hz battery compartment. B Plug your aerial into the ANT IN socket of the video. [. . . ]