User manual DAEWOO VQ SERIES [GENERAL]

[. . . ] Video recorder For model number, see the front display of your video. The following standard functions are available on this set. Instruction manual NTSC playback See page 14 MESECAM tape playback See page 14 Index scan See page 15 Wide-screen pictures See page 16 Commercial skip See page 16 High-speed rewind 4156 Important: If you switch the video off at the mains supply overnight, you do not have to retune the video. Simply press and then MENU on the remote control to restore all the programme settings. See back cover for quick - start guide Helpline number: 0118 925 2577 With queries, please quote the page number, reference number and model number. 7/1997 Worth knowing Please keep the video's guarantee sheet (pages 29 and 30) and receipt for your video in a safe place. Precautions x x x Read this booklet carefully. Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. [. . . ] To release the remote lock, press and hold until n disappears from the front display. 17 Simple recording . VCR P-01 L R Load a cassette with its safety tab in place (see page 23). STOP SP PRO1 BBC1 STEREO ON SV/V+ 1 2 3 TV/VCR Press PR+ or PR- to choose the station you want to record. Press SP/LP if you want to double the length of the cassette's recording time. For example, on an E240 cassette you can record for up to four hours when SL is displayed, or up to eight hours when LP is displayed. 4 5 6 AV 7 8 9 A 30 0 A. D Q. S VCR REC L R Press to start your recording. VCR REC L R Press I I if you want to stop the recording for a short while. `REC' on the front display will blink. Press to continue recording. EJECT SP/LP PR + MENU VCR PAL/SEC OK P-01 L R Press to stop your recording. ­ INDEX + PR ­ A. SEL One-touch recording ­ OTR These buttons are used on the following two pages. VCR TMR R0:30 L R Press PR+ or PR- to choose the station you want to record. Every time you press , the recording time will increase by 30 minutes. It is possible to record for up to 10 hours if there is enough room on the cassette. x x To cancel OTR press and hold the until the video stops recording. button for about five seconds If you want to record from other equipment that is connected to your video, see pages 5, 6 and 9. 18 Recording cassettes x x If you want to use the video's timer to record a programme, the clock, date, and stations must be set correctly. Load a cassette with its safety tab in place (see page23) and with enough free tape for the recording. Timer recording using VideoPlus+ VideoPlus is an automatic system which makes it easier to set the timer. VideoPlus VideoPlus Number 83077---- 1 Press SV/V+ to select the VideoPlus screen. (If this button is not on your remote control, the function is not available on your video. Videoplus numbers are shown in TV guides. From your current TV guide, type in the number next to the programme you want to record using the number buttons 0 - 9. Press OK to confirm. 0-9:VideoPlus number :correct OK:confirm MENU:end How often do you want to record this program? 2 Once Weekly (once a week) Daily (Mon-Fri) Daily (Mon-Sat) Daily (Mon-Sun) PR+/-:select OK:confirm MENU:end Press PR+or PR- to select how often you want to make the recording, for example, once, weekly and so on. Press OK to confirm. 3 TIMER PROGRAM(Once) PR 03 Start Time 21:20 End Time 22:20 Start Date 20/09(SAT) Tape Speed SP PDC ON / :correct OK:confirm MENU:end If you want to change any details. Move to the details you want to change using the and buttons. Change the setting using the PR+ or PR- or number buttons 0-9. If all the settings are correct, press or until you see `OK: confirm' on the bottom line of the screen. Press OK to confirm. 4 TMR 20:00 Press to switch your video off. Your video will not record unless you do this. You can switch the video on again if you want to set the timer to record another programme. Remember to switch the video off when you have finished setting the timer. If PDC does not appear on the screen, it is not available on your video. PDC = Programme Delivery Control. x PDC sets your video to adjust the start and end times of your timed recording. This happens even if a programme starts earlier or later than advertised. PDC works when the broadcaster sends a signal, but the signal is not always sent. If you are not sure the signal will be sent, it is best to switch PDC off. x x x x If there is no programme number displayed under `PR' in the change menu, the video doesn't yet know the number for the programme you want. Type it in and this will be stored for later recordings. [. . . ] If the TV/VCR button on the video remote control does not work, read the instruction book for the TV to find out about an audio video button. The video has a number other than 52 when RF appears A number other than 52 might be displayed on the video when RF is flashing in the display. This means that the number has been adjusted in the past. The TV needs to be tuned in to get the blue autoset or autosearch screen. 31 Quick-start guide Please follow the guide from the beginning to the end. [. . . ]