User manual DAEWOO VQ812PL

[. . . ] Instruction manual Video recorder The following standard functions are available on this set. UK Eng lish For model number, see the front display of your video This manual covers the `VQ' range. NTSC playback See page 14 See page 14 MESECAM tape playback Index scan See page 15 Wide-screen pictures Commercial skip See page 16 See page 16 4156 High-speed rewind Crystal Mark Clarity approved by Plain English Campaign See back cover for quick-start guide Helpline number: 0118 925 2605 With queries, please quote the page number, reference number and model number. WORTH knowing Please keep the video's guarantee sheet (pages 29 and 30) and receipt for your video in a safe place. Precautions x x x x x x Read this booklet carefully. Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. Read this chapter and the "Setting up your video" chapter to help you set up and adjust your video recorder. Do not put the video recorder in a hot or humid place (to avoid the risk of fire and electric shock). [. . . ] Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. If you wish to changes any details: Move to the details you want to change using the / buttons. Change the setting using the PR+ or PR- or number buttons 0-9. If all the settings are correct, press or until you see `OK:confirm' on the button line of the screen. Your video will not record unless you do this. 2 How often do you want to record this program? Once Weekly(Once a Week) Daily(Mon-Fri) Daily(Mon-Sat) Daily(Mon-Sun) PR+/-:select OK:confirm MENU:end 3 TIMER PROGRAM (Once) PR 03 Start Time 21:20 End Time 22:20 Start Date 20/09(MON) Tape Speed LP PDC ON / :correct OK:confirm MENU:end 4 TMR You can switch the video on again if you want to set the timer to record another programme. Remember to switch the video off when you have finished setting the timer. If PDC does not appear on the screen, it is not available on your video. · PDC sets your video to adjust the start and end times of your timed recording. This happens even if a programme starts earlier or later than advertised. PDC works when the broadcaster sends a signal, but the signal is not always sent. If you are not sure the signal will be sent, it is best to switch PDC off. · · · · · If there is no programme number displayed under `PR' in the change menu, the video doesn't yet know the number for the programme you want. Type it in and this will be stored for later recordings. If you wish to record from a satellite receiver, select under `PR' the satellite programme or AV (depending whether the video is connected with the antenna cable or the scart-cable). Leave the satellite tuner switched on and set the programme you want to record. The video will warn you if you have set the timer to start to recording a second programme before the first recording has finished. To stop the recording after it has already started, press and hold the STOP button for about five seconds until the video stops recording. VideoPlus + and Plus code are trademarks of Gemstar Development Corporation. VideoPlus + system is manufactured under license from Gemstar Development Corporation. 19 x x For timer recordings, clock, date, and stations must be set correctly. Load a cassette with its safety tab in place (see page 23) and with enough free tape for the recording. Normal timer recording How often do you want to record this program? 1 SV/V+ Once Weekly(Once a Week) Daily(Mon-Fri) Daily(Mon-Sat) Daily(Mon-Sun) PR+/-:select OK:confirm MENU:end 1 2 3 TV/VCR 4 5 6 AV 7 8 9 Press MENU. Choose "Timer Program" by pressing OK. Press PR+ or PR- to select an unused channel, for example `- - - -' then press OK to confirm. There are positions for eight timer programs. [. . . ] When the small VCR symbol appears on the display, you can only change channel by using the video remote control. If the TV/VCR button on the video remote control does not work, read the instruction book for the TV to find out about an audio video button. The video has a number other than 52 when RF appears A number other than 52 might be displayed on the video when RF is flashing in the display. This means that the number has been adjusted in the past. [. . . ]