User manual DAEWOO WM-501

[. . . ] PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER Please observe the following instructions. Operate the Selector Switch to run or stop the unit. - Do not use Main Power Switch or Auxiliary Power Switch to operate unit. Do not stick anything into the air outlet or inlet. [. . . ] Mark the center of window sill with a pencil. Insert Screws (Type A) into the sill bracket. Attach Sill bracket to window sill using Screws (Type B). (The outside edge of window bracket should be 5. 9 in (150mm) from center line) 6. Place the carpenter's level on the sill and the outdoor end of Sill Bracket. Turn Screw (Type A) until the level's bubble is centered. Screw (Type B) SILL BRACKET OUTER WINDOW SILL CENTER LINE INNER WINDOW SILL SILL BRACKET Screw (Type A) OUTER WINDOW SILL WALL 140 70 90 UNIT 150mm (5. 9in) INNER WINDOW SILL SASH BRACKET 38 145 (130) 55 (135 MAX) SILL BRACKET 5 · Step 3 - Placing Unit in Window CAUTION 1. To avoid injury or accident, it is strongly recommended that you have additional help when lifting the unit. Personal injury or property damage may result if unit falls from window. 1. Attach Sash Bracket in the left side and right side of the unit. (Screws are ready provided in the each side as part of the Air-Conditioner for this purpose. So, at first, please remove this screws, and re-attach Sash Bracket to the same portion with Screws (Type C) of components for installation. ) 2. Insert Window Kit Frame into the upper and bottom guides of the unit. Fasten window shutter in the window kit frame with Screws (Type D) in the left side and right side of the unit. Open the window and place the unit in the center of the window sill. The attached sash bracket in the unit's side have sharp edges. it is needed that you have careful when lifting the unit. (1) Remove the attached screw Cabinet (2) Insert Sash Bracket between Cabinet and Base Pan (3) Attach Sash Bracket with the screw of (1) and the screw of components of installation Screw (Type C) WINDOW KIT FRAME PLATE WINDOW TOP (upper guides) WINDOW SHUTTER (bottom guides) Screw (Type C) SASH BRACKET Screw (Type D) · Step 4 - Install Sash Bracket CAUTION Do not drill into window frame until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located the frame. Fasten Sash Bracket be attached in the unit's side with Screw (type C) on the window sill. (It is the same to install Sash Bracket left side and right side. ) 2. Fasten Sash Bracket with Screw (Type C) to top of indoor window sash or directly into side of window sash or directly into side of window frame. This will prevent the raising of the window from the outside. If you have a hard wood or metal window frame, a 1/8 inch pilot hole may be needed in order to drive the screw. 6 SASH BRACKET WINDOW FRAME WINDOW SASH Screw (Type C) · Step 5 - Secure Window Shutter CAUTION Do not drill into window sash until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located in the frame. To provide a proper seal, pull each expandable side Window Shutter out and up until it is tight against the window frame. [. . . ] The marked rating of the extension cord should be 125V 13A (Min. ). WARNING : To avoid death, personal injury or properly damage due to electrical shock, do not use an extension cord or pinch the power cord. Do not remove the warning tag from the power cord. 12 BEFORE CALLING FOR SERVICE When you find something wrong with your room air conditioner, please carefully check the following items. If you are unable to find the cause of trouble, contact your service dealer. Difficulty · Air conditioner does not operate. Possible Cause · No power to unit. Suggested Solution · Confirm power cord is plugged in. · Verify main power switch (main circuit breaker) or fuse of the unit is good. [. . . ]