User manual DAHON I-MOTION 3

[. . . ] at a traffic light. i-MOTION 3 connecting link i-MOTION 3 shifter Intuitive gear indication, highquality design. Easy wheel removal: The gear adjustment remains unchanged. i-MOTION 3 · June 2006 4 O P E R AT I O N SHIFTING 1 Shift gears by turning the rotating grip. 1 E » You can shift while standing still or while riding your bicycle. [. . . ] Let cleaner set for only a few minutes and rinse with water. Do not oil chain until completely dry. LUBRICATION » The rear wheel hub is provided with permanent lubrication and maintenance-free under normal conditions. » Regular lubrication will extend the chain's service life. 10 i-MOTION 3 · June 2006 MAINTENANCE AND CARE REPAIR WORK / WEAR PARTS REPAIR WORK Only a qualified bike dealer should perform any necessary work on the gear hub, shifter, and brakes. » Unauthorized work on your i-MOTION 3 system could endanger you and your warranty may become void. » Please contact your qualified bike dealer regarding any questions or problem you may have. Back pedal brake If the back pedal brake is braking too hard, the brake jacket has to be lubricated with special grease. This work must be performed by a qualified bike dealer. Cable Change If a cable must be replaced (shifter cable or brake cable), contact your qualified dealer. WEAR PARTS Brake liners or brake jackets, brake cables, shift cables, handlebar grips, sprockets, and bike chains are wear parts. Please check these parts regularly and replace them timely. E i-MOTION 3 · June 2006 11 A S S E M B LY OF COMPONENTS A S S E M B LY H U B » Spoke the hub as normal. Set the dust cover (1) onto the 16 1 16 driver. The curve must point to the outside. 17 driver. Set the sprocket (2) onto the If an offset sprocket will be used, mount the sprocket with the curve pointing to the outside. 17 2 18 ring (3) onto the driver. Check proper seat of the retaining ring. Mount the sprocket retaining 19 onto the axle end of the Slide the cable stop bracket (4) 18 3 sprocket side. Thereafter mount the washer with rubber insert (5) to fix the the cable stop bracket. » Place the rear wheel into the rear frame. 19 4 5 12 i-MOTION 3 · June 2006 A S S E M B LY OF COMPONENTS 20 each (6) onto each axle end. The serrations of the retaining washer must bear against the dropout of the frame. Align the stop 21 parallel tocableframebracket (7) the stay (8). Slide one retaining washer 20 6 E 22 tighten them alternately with a torque of 30 ­ 40 Nm (266 ­ 350 in. lbs. ). Mount the axle nuts (9) and 21 7 23 lever (10) between the two If applicable, mount the brake 8 straps of the frame clamp (11). The frame clamp must be seated on the frame without play. [. . . ] i-MOTION 3 · June 2006 16 A S S E M B LY OF COMPONENTS E i-MOTION 3 · June 2006 17 T E C H N I C A L D ATA GEAR HUB Speeds Brake Over Locknut Dim. , OLD Length, L Axle Ends Diameter Holes Spoke Hole Diameter Hole Ref. ø, HR Total Ratio Gear jump 1 to 3 Compat- Chain ibility Chainline, CL Dimension Sprocket Shifter Tandem Dropout Width Dim. , A i-MOTION 3 with back pedal brake 3 With back pedal brake 130 mm 168 and 178 mm M 10x1 min. 8 mm 28 / 32 / 36 3. 0 mm 70 mm F1 = 27. 3 mm / F2 = 27. 6 mm 186 % 36% / 36% 44. 0 mm (straight spr. ) / 40. 5 mm (off-set spr. ) 1 Flange Dist. [. . . ]