User manual DAIKIN ALTHERMA EKHBRD016AAV1

[. . . ] OPERATION MANUAL Indoor unit for air to water heat pump system and options EKHBRD011AAV1 EKHBRD014AAV1 EKHBRD016AAV1 EKHBRD011AAY1 EKHBRD014AAY1 EKHBRD016AAY1 EKHBRD011AAV1 EKHBRD014AAV1 EKHBRD016AAV1 EKHBRD011AAY1 EKHBRD014AAY1 EKHBRD016AAY1 Indoor unit for air to water heat pump system and options Operation manual CONTENTS Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scope of this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick start-up of the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] [b-03] set point: storage temperature (see figure "Domestic water heating modes" on page 6). [b-02] Status: defines whether the weather dependent domestic water heating is turned ON (1) or OFF (0). If enabled, the storage set point will be set weather dependent. In case of a higher ambient temperature (e. g. during summertime), temperature of supply water to the domestic hot water tank will be higher too, so that storage temperature set point can be set lower in order to keep the overall equivalent hot water amount the same during the whole year. Therefor it is recommended to use this function. Remark that the w icon will only be blinking during effective operation. During the operation it is always possible to cancel the operation by pushing the w button once. Be aware that after pushing the w button, it is possible that the permanently lit w icon still displays, meaning that the reheat function is enabled. The storage temperature set point is a field setting. Refer to the chapter "Field settings" on page 14 for a detailed description how to set one or more field settings. [b-03] Set point: storage temperature (see figure "Domestic water heating modes" on page 6). [b-02] Status: defines whether the weather dependent domestic water heating is turned ON (1) or OFF (0). If enabled, the storage set point will be set weather dependent. In case of a higher ambient temperature (e. g. during summertime), temperature of supply water to the domestic hot water tank will be higher too, so that storage temperature set point can be set lower in order to keep the overall equivalent hot water amount the same during the whole year. Therefor it is recommended to use this function. T 70°C T 70°C 55°C A 15°C A T NOTE 55°C 25°C Ambient temperature Domestic hot water storage temperature 15°C A T NOTE A 25°C Ambient temperature Domestic hot water storage temperature The temperatures for weather dependent domestic water heating (see figure) are fixed and can not be changed. The temperatures for weather dependent domestic water heating (see figure) are fixed and can not be changed. EKHBRD011~016AAV1+Y1 Operation manual 7 Indoor unit for air to water heat pump system and options 4PW54466-1A Manual storage is deactivated automatically when the set point for the domestic hot water storage temperature is reached. It can also be stopped at any time by pushing the w button. Other operation modes Start up operation (d) Reheat This mode will prevent the domestic hot water from cooling down lower than a certain temperature. When enabled the indoor unit will deliver hot water to the domestic hot water tank when the reheat minimum value is reached. The domestic water heating will continue until the reheat maximum temperature is reached. Selecting reheat operation for domestic water heating 1 Use the w button to enable reheat operation. The w icon will display. NOTE During start up, the d icon displays, indicating that the heat pump is starting up and is not working in a steady state condition. Defrost operation (d) In space heating operation or domestic water heating operation, freezing of the outdoor heat exchanger may occur due to low outdoor temperature. If this risk occurs, the system goes into defrost operation. It reverses the cycle and takes heat from the indoor system to prevent freezing of the outdoor system. [. . . ] When exiting FIELD SET MODE, "88" may be displayed on the remote controller LCD while the unit initializes itself. NOTE EKHBRD011~016AAV1+Y1 Operation manual Indoor unit for air to water heat pump system and options 4PW54466-1A 14 NOTE When running through the field settings you may notice that there are some more field settings as there are mentioned in the "Field settings table" on page 15. These field settings are not applicable and may not be changed! Field settings table Installer setting at variance with default value First code Second code Setting name Date Value Date Value Default value Range Step Unit 0 Remote control setup 03 Status : space heating schedule timer mode 1 (ON) 0/1 -- -- 1 Automatic storage timing for domestic water heating 00 01 02 03 Status: night time storage Night time storage start time Status: day time storage Day time storage start time 1 (ON) 1:00 0 (OFF) 15:00 0/1 0:00~23:00 0/1 0:00~23:00 -- 1:00 -- 1:00 -- hour -- hour 2 Automatic setback function 00 01 02 Status: setback operation Setback operation start time Setback operation stop time 1 (ON) 23:00 5:00 0/1 0:00~23:00 0:00~23:00 -- 1:00 1:00 -- hour hour 3 Weather dependent set point 00 01 02 03 Low ambient temperature (Lo_A) High ambient temperature (Hi_A) Set point at low ambient temperature (Lo_Ti) Set point at high ambient temperature (Hi_Ti) ­10 15 70 45 ­20~5 10~20 25~80 25~80 1 1 1 1 °C °C °C °C 4 Disinfection function 00 01 02 Status: disinfection operation Disinfection operation day selection Disinfection operation start time 1 (ON) Fri 23:00 0/1 Mon~Sun 0:00~23:00 -- -- 1:00 -- -- hour 5 Automatic setback and disinfection set point 00 01 02 03 Set point: disinfection operation temperature Disinfection operation time duration Leaving water setback temperature Room setback temperature 70 10 5 18 60~70 5~60 0~10 17~23 5 5 1 1 °C min °C °C 8 Option setup 03 Status: low noise level 1 1~3 1 -- b Domestic hot water set points 00 01 02 03 Set point: reheat minimum temperature Set point: reheat maximum temperature Status: weather dependent domestic water heating Set point: storage temperature 35 45 1 (ON) 70 35~65 35~75 0/1 45~75 1 1 -- 1 °C °C -- °C Operation manual EKHBRD011~016AAV1+Y1 15 Indoor unit for air to water heat pump system and options 4PW54466-1A MAINTENANCE Maintenance activities In order to ensure optimal availability of the unit, a number of checks and inspections on the unit and the field wiring have to be carried out at regular intervals, preferably yearly. This maintenance should be carried out by your local Daikin technician (see installation manual). The only maintenance which may be required by the operator is: keeping the remote controller clean by means of a soft damp cloth, checking if the water pressure indicated on the manometer is above 1 bar. [. . . ]