User manual DAIKIN BRC944A2B

[. . . ] Do not put a finger, a rod or Do not attempt to repair, other objects into the air relocate, modify or reinstall outlet or inlet. the air conditioner by yourself. Prohibited Putting a heavy object on the cord, heating it, or pulling it may cause breakage which leads to electric shock or fire. Prohibited It will affect your physical conditions and cause health problems. Prohibited As the fan is rotating at a high speed, it will cause injury. Prohibited Incorrect work will cause electric shocks, fire etc. For repairs and reinstallation, consult your dealer. If anything abnormal such as a burning smell occurs, stop the operation immediately and turn the breaker OFF. If the air conditioner is not cooling or heating properly, the refrigerant may be leaking, so consult your dealer. Check with a qualified repairman before attempting any repairs, which might accompany addition of refrigerant. [. . . ] For installation, consult the service shop where you bought the unit or a qualified technician. CAUTION The air conditioner must be earthed. Incomplete earthing may result in electric shocks or fire. Do not connect the earth line to a gas pipe, water pipe, lightening rod, or a telephone earth line. Do not connect the air conditioner to a power supply different from the specification. It may cause trouble or fire. Depending on the environment, an earth leakage breaker must be installed. Do not install the air conditioner in places where flammable gas may leak. Arrange the drain hose to ensure smooth drainage. Lack of an earth leakage breaker may result in electric shocks or fire. Prohibited If leaked gas should accumulate near the unit, fire may occur. Incomplete drainage may cause wetting of the building, furniture etc. 3 Names and Functions of Parts Run indicator lamp (green) Display Displays the operating conditions. (All displayed here for your reference) ON/OFF button Press to start the system. Press again to stop the system. Timer select button Selects one of the following: One time timer ON Daily timer ON Timer OFF Mode select button Selects an operation mode. ( page 6) Swing button ( page 8) Airflow rate button Clock setting button ( page 5) Adjusts the airflow rate. Time setting button for the timer Timer setting button Sets the current time and timer. Temperature adjustment button Adjusts the temperature setting. CAUTION This remote controller cannot be used together with a standard wireless remote controller. Otherwise, what appears on this remote controller's display may fail to correspond to actual operating conditions. 4 Preparation before Operation Checking the power If nothing appears on the remote controller's display, turn on the circuit breaker. Setting the current time 1 Press . The current time starts blinking. lights up. 2 2 Press and set the current time. 1. 3 Keep pressing the button, and the time advances fast. 3 Press . blinks. (This completes the current time setting) The clock's accuracy is ±30 seconds per month. Notes To use the unit efficiently Avoid overcooling or overheating. Moderate room temperature setting contributes to power saving. Recommended temperature setting For cooling ·············· 26~28°C For heating ············· 20~22°C Please take note of the following points Electric power is consumed even when the air conditioner is not in operation. When the unit is not used for a long period of time such as during off-season, turn off the breaker. Operating conditions If the operation is continued under any conditions other than the following, the safety device may work to stop the operation. Also, dew may form on the indoor unit and drip from it. (Cooling/DRY) Cooling DRY Heating Hang a blind or a curtain on the window. This will enhance the cooling/heating effect by intercepting direct sunlight and drafts. A clogged air filter will reduce the cooling/heating effect, leading to waste of power. Clean the air filter monthly (every two weeks as required) or so. Outdoor temp. Room temp. -10 to 46°C 18 to 32°C Less than 80% -10 to 46°C 18 to 32°C Less than 80% -15 to 20°C Less than 27°C Operation limit differ according to the model. 5 Automatic · DRY · Cooling · Heating Operation Select your desired operation mode. Once preset, the system can get restarted in the same operation mode. 1 Run indicator lamp (green) to select your desired Press operation mode. Each time the button is pressed, the mode changes as follows. 2 (Automatic) (Heating) (DRY) (Cooling) Heat pump model 1 (DRY) (Cooling) Cooling only model The system does not have the FAN mode. 2 Press . The run indicator lamp lights up. To stop the operation: Press again. The run indicator lamp goes out. Automatic operation In Automatic, the temperature setting and operation mode (DRY, Cooling or Heating) are automatically selected according to the room temperature and outdoor temperature at the time of starting operation. DRY operation In this mode, humidity is removed from the air. Note While running in the DRY mode, you may feel cool or warm air from the air outlet. In such case, readjust the airflow direction with the vertical airflow direction blades. (except Duct Connected type) 6 To adjust the temperature and airflow rate: Operation mode Setting to be adjusted Automatic Cooling Heating DRY Temperature cannot be adjusted. Temperature is adjustable. Recommended temperature Cooling : 26°C-28°C Heating : 20°C-22°C (Temperature) Five levels of airflow rate setting from " " to " " plus " " are available. (Airflow rate) Airflow rate cannot be adjusted. When the unit runs in the cooling or heating mode at a low airflow rate, the cooling or heating effect may be insufficient. To adjust the airflow direction: ( page 8) Heating operation Since the heating operation is performed by taking the heat from outdoor into the room, the heating capacity decreases as the outdoor temperature lowers. If the room is not heated sufficiently, it is recommended to use other heating appliance at the same time. Since the air conditioner heats the whole room by circulating hot air, it takes some time to heat the entire room completely. [. . . ] (The daily timer is now programmed. ) Note If the following appears on the display, the timer must be reprogrammed. The 24-hour timer display is blinking. The 24-hour timer display is blinking. This means that Timers and are programmed for the same time settings. New time settings must be made. This means that the timer has not been programmed yet. 13 Cleaning Cleaning the remote controller Wipe it clean with soft, dry cloth. Do not use any water hotter than 40°C, volatile liquid such as benzine, gasoline and thinner, polishing powder, and anything hard such as scrub brush. When the unit is not used for a long time On a sunny day, keep the system running for half a day in the FAN mode to dry it up inside. [. . . ]