User manual DALLEE ELECTRONICS NORFOLK & WESTERN Y6B SOUND

[. . . ] IN LOCOMOTIVE DELUXE N&W Y6A, Y6B, STEAM SOUND for various track power by Version 1. 0 CAUTION-THIS DEVICE CAN BE DAMAGED BY STATIC DISCHARGE. PLEASE EXERCISE CARE DURING INSTALLATION TO AVOID THIS POSSIBILITY. DISCHARGE YOURSELF TO AN ELECTRICAL GROUND (OUTLET COVER SCREW) BEFORE REMOVING THIS DEVICE FROM ITS ANTI-STATIC BAG. PLEASE READ INSTRUCTION SHEET COMPLETELY BEFORE ATTEMPTING TO INSTALL AND OPERATE THIS PRODUCT. [. . . ] The connections are the same for each optical sensor. SYNC wire Optical Sensor White. . . . . . . . . . . . . . . . . . . . . . . . . Black & Green Red. . . . . . . . . . . . . . . . . . . . . . . . . . . . Red The optical sensor needs to be mounted so that the front focal distance is 1/8" to 1/4" maximum. With the sound system "ON", the optics can be easily aligned since an exhaust chuff can be heard from any white (reflection) to black (no reflection) transistion. Gray Red Lighting: Red wire is a regulated +5 volts which is common to all lamps. All outputs are pulled to ground ("-") to turn the lamps or LED's on. Exceeding the current rating will damage the output driver. Aux. Tender #756 Speaker connections: SPKR - main speaker Red & gray wire pair connect to tender speaker. Backup light #756 (5v) W B R Definitions of connections to be shown on later pages: Red Black White White Black Red Main Board G R Gray Red CONN1: 1 - RED . . . . . . . . . . . . . Motor 1 2 - BLACK. . . . . . . . . Motor 2 3 - WHITE . . . . . . . . . track RF input (for DC operators only) CONN2: 1 - RED . . . . . . . . . . . . . DCC rail 1 . . . . . . . . . . also AC input 1 2 - GRAY. . . . . . . . . . . DCC rail 2 . . . . . . . . . . also AC input 2 unlabeled, battery select jumper: on - rechargeable batteries. . . . . . . . . off - standard batteries batt: 1 - RED . . . . . . . . . . . . . DC power "+" 2 - GRAY. . . . . . . . . . . DC power "­" SW1: 1 - RED . . . . . . . . . . . . . switch common 2 - GRAY. . . . . . . . . . . switch open CONN3 - this connector mates to the Volume/Treble/Bass board (not shown) cable. 3 G R G R G R dccF1 1 - Whistle (red) 2 - Bell (gray) dccF2 1 - Cylinder Blow Down (red) 2 - Simple / Compound (gray) G R G R G R G R G R DC track power installation using batteries & DALLEE controller #755 Connect all wires between boards as shown on page 3. Place the Engine Board in an appropriate location in the engine. Also place the choke in the engine as shown. It is important to make all of the previous connections from the right rail to move to the side after the choke. While the drawing shows the motor, previously installed lighting, and a smoke unit, your engine may not contain all of them. You may also wish to change the factory installed lighting to that supplied from the sound cards. Failure to connect other power drawing items to the other side of the choke will result in the LocoMaticTM Controller to not be able to operate the sound system properly. Engine Board White Black Red White CHOKE * DC motor lighting circuits Smoke Unit Right Rail pickup Left Rail pickup The Aux Tender lamp is controlled via the LocoMaticTM Controller's "Aux2" function (Cntrl-Aux buttons together). Red Black White *Larger motors require a larger capacity choke. Chokes: Item 702 - 1. 5 ampere loads Item 703 - 5. 0 ampere loads Gray ON / OFF switch White #566 SPST switch. Switch shown in the OFF position. Lighted car / other engines used in consist preparation. You will know if this is necessary by placing the locomotive / lighted cars on the track and then attempting to blow the Whistle or operate the BELL. If they do not operate with the other items on the track then you need to do the following. We suggest doing this to all lighted cars or engines used in the same consist since it lets the signal stay at it's maximum level. [. . . ] The unit can be broken into smaller strip lengths where needed. Install in cabooses, passenger cars, buildings or other locations. Measures only 1/2" wide with a full 16" in total length. The power section of this lighting strip, when separated from the rest of the strip would measure 1/2" x 2". [. . . ]