User manual DANA 4150-23

[. . . ] This appliance is intended to be used in household and similar applications such as: - staff kitchen areas in shops, offices and other working environments; - farm houses; - by clients in hotels, motels and other residential type environments; - bed and breakfast type environments. -20• To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance). [. . . ] If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the amount of detergent used accordingly. The number and type of wash cycles and options may vary depending on the dishwasher model. Pre-wash for dishes while awaiting completion of the load with the dishes from the next meal. Environmentally-friendly wash cycle with low energy consumption levels, suitable for pans and dishes. Economic and fast wash to be used for lightly soiled dishes. (Run cycle immediately after use) (2 plates + 2 glasses + 4 pieces of cutlery + 1 saucepan + 1 small frying pan). Economic and fast wash for delicate items which are sensitive to high temperatures. (Run cycle immediately after use) (glasses upper rack + delicate plates, lower rack). Disinfecting wash cycle suitable for washing bottles, rings and teats together with plates, cups, glasses and cutlery. The crockery should only be loaded on the upper rack. Auto Normal 29 g (A) 6 g (B) 29 ml (A) 6 ml (B) 1 (A) Yes A–B–C-D 1:50’ 25 g (A) Daily A 60 25 ml (A) 1 (A) No A–B– C 1:00’ Soak No No No No A–B 0:08’ Eco* 29 g (A) 6 g (B) 29 ml (A) 6 ml (B) 1 (A) Yes A–B-C-D 2:55’ 25 g (A) 25 ml (A) 1 (A) No A -C 0:25’ 35 g (A) Crystal 35 ml (A) 1 (A) Yes A–B–C 1:30’ 20 g (A) Baby Wash 20 ml (A) No Yes A 1:20' Notes: Optimum performance levels when using the "Daily wash" and "Speed wash" cycles can be achieved by observing the maximum amounts of crockery specified. • If drops of water remain on the crockery or if there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). Setting the water hardness Every dishwasher is equipped with a water softener which, by using refined salt designed especially for this type of appliance, supplies water without limescale which is then used to wash the crockery. This dishwasher offers a setting which helps to reduce pollution and optimises washing performance in accordance with the water hardness level in your area. This information can be obtained from the organisation which supplies your household with water. The water hardness adjustment procedure may vary depending on the dishwasher model purchased. - Switch on the appliance by pressing the ON/OFF button. - Press and hold the P button for a few seconds; after a short beep sounds, the water hardness setting will appear on the display and the Start/Pause button will begin to flash (the default water softening system setting is level !- Press the P button repeatedly until the desired hardness level has been reached (1-2-3-4-5* see Water hardness table). The selected water hardness value will appear on the display. In order to achieve the best possible results using a wash cycle, make sure that the dispenser is never empty. Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery. [. . . ] € The level of the refined salt is low or the dosage setting is not suited to the hardness of the water (see Rinse aid and salt). € The lid on the salt dispenser is not closed properly. € The rinse aid has been used up or the dosage is too low. • The rinse aid dosage is too high. [. . . ]