User manual DANA 4360-128

[. . . ] Pass them on to possible new owners of the appliance. Also be equipped with vents to allow gas to escape in the event of a leak. As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc. It is advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, fireplaces, stoves, etc. [. . . ] If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Check that the pressure of the gas supply is consistent with the values indicated in Table 1 (“Burner and nozzle specifications”). This will ensure the safe operation and longevity of your appliance while maintaining efficient energy consumption. connection with a rigid pipe (copper or steel) !Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. 3 GB There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (seal provided with appliance). These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. Checking the tightness of the connection !€ Adjusting the burners’ primary air : Does not require adjusting. • Setting the burners to minimum: 1. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. 78 MJ/m³ A R S S RR A TC S R A Ø145 S 7HPC 640 /HA 7HPC 640 X/HA 7HPC 640 GH/HA 7HPC 640N /HA 7HPC 640N GH/HA 7HPC 640N X /HA PC 640N /HA PC 640N X/HA GPC 64 R GH RU/HA GPC 64 R GH RU/HA GPC 64 N X RU/HA GPC 64 N GH RU/HA GPC 64 N RU/HA 7HPC 631 /HA 7HPC 640 T GH /HA 7HPC 631 X/HA 7HPC 640 T R /HA 7HPC 640 T X /HA GPC 64 T R GH RU/HA GPC 64 T R GH RU/HA DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 5 Description of the appliance GB Overall view GAS BURNERS Support Grid for COOKWARE Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. € Control Knobs for GAS BURNERS adjust the size of the flame. • GAS BURNER ignition* enables a specific burner to be lit automatically. € SAFETY DEVICE* stops the gas flow if the flame is accidentally extinguished. The position of the corresponding gas burner or electric hotplate* is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: • Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. [. . . ] This procedure must be performed by a qualified technician authorised by the manufacturer. Do not use abrasive or corrosive detergents such as stain removers, anti-rust products, powder detergents or sponges with abrasive surfaces: these may scratch the surface beyond repair. Never use steam cleaners or pressure cleaners on the appliance. € It is usually enough to wash the hob with a damp sponge and dry it with absorbent kitchen roll. [. . . ]