User manual DANBY DAC10560DE

[. . . ] Room Air Conditioner Model · Modèle The model number of your room air conditioner is found on the serial plate located on the right side of the unit above the power cord. All repair parts are available for purchase or special order when you visit your nearest service depot. To request service and/or the location of the service depot nearest you, call the TOLL FREE NUMBER: 1-800-263-2629 When requesting service or ordering parts, always provide the following information: · · · · Product Type Model Number Part Number Part Description DAC9006DE DAC10560DE USE AND CARE MANUAL MANUEL D'UTILISATION Models · Modèles For service, contact your nearest service depot or call: Climatiseur de pièce Le numéro de modèle de votre climatiseur se trouve sur la plaque d'information qui se trouve sur le coté droit de l'appareil par dessus le cordon d'alimentation. Toutes les pièces de rechange ou commandes spéciales sont disponibles de votre centre régional de service autorisé. [. . . ] Fixer le support de fermeture sur chaque côté (en bas) des volets, et fixez au rebord de la fenêtre en utilisant une vis de 3/4 po sur chaque côté. 5. Cadre de la fenêtre 1. Assembly of the Upper Channel, to Cabinet. (Factory installed on some models) "L" Shaped Top Channel: Install the "L" shaped channel to the top of the cabinet as shown in Fig. 3 using four (4) 3/8" screws. 3/8" Screw 3a. Completing the Installation (cont'd) · Carefully place the air conditioner into the window with the "L" shaped mounting bracket (on top) positioned in front of the upper window sash. The bottom of the cabinet should be positioned on the "recessed" portion of the window frame. Pull the window down until it rests just behind the front flange of the (top) "L" shaped mounting bracket. Expand the shutter frames (fully) on each side and secure the top of the frames to the window sash using one 3/4" screw on each side and one in the "L" shaped mounting bracket. 5 Secure the shutter clamp on each side of the (lower) shutter and secure to window sill using one 3/4" screw on each side. Fig. 5 · · Canal en forme de « L» "L" Shaped Mounting Bracket · · "U" Shaped Channel (Factory Installed) Fig. 3 Canal en forme de « U » Fig. Montage des rideaux latéraux au caisson. · Étendez les volets et glissez-le dans les support de volets sur le canal latéral du climatiseur comme montré dans fig. Faites glisser les cadre des volets dans les canaux supérieur (en forme de "L") et inférieur (en forme de "U") Ces volets sont identifiés (sur le cadre) en tant que volets gauches et droits. · vis de 3/4 po 2. · Assembly of the Side Curtains to Cabinet. Extend the shutter from the shutter frame and slide it into the shutter guide on the side channel of the air conditioner as shown in Fig. Slide the shutters into the top ("L" Shaped) and bottom ("U" Shaped channels. The shutters are identified (on frame) as left & right. Sl id e 3/4" Screws Window Sash · Canal supérieur en forme de "L" Fig. 5 support de fermeture · "L" Shaped Mounting Bracket Fig. 5 Shutter clamps Coupez la bande mousse adhésif afin qu'elle s'ajuste adéquatement à l'ouverture entre le haut de l'intérieur et de l'extérieur de la fenêtre puis fixer le serrure de sûreté sure le cadre du fenêtre extérieur en utilisant une vis de 3/4 po. 6. do w n z se lis G rs ve le s ba in to gu id e · Place the second foam sealing strip to fit the opening between the inside and outside windows then attach the safety lock to the outside window frame using one 3/4" screw. 6. serrure de sûreté Scellement mousse (adhésif) Shutter vis de 3/4 po Volets Cadre des volets Fig. 4 3/4" Screw Safety Lock Foam Seal 4. [. . . ] During the next fourty-two (42) months any part of the sealed system found to be defective (consisting of compressor, condenser, evaporator, dryer and all related tubing) will be replaced without charge. The purchaser shall pay for all labor and return freight during this period for repair or replacement of any sealed system components. Any unit being diagnosed as non-functional due to sealed system failure and warranting an exchange will be subject to an appropriate depreciation or user fee, including any and all freight charges being levied against the consumer. Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service must be performed by a qualified service technician. [. . . ]