User manual DANBY DAC7006DE

[. . . ] Do NOT insert anything between the air flow blades, as the inner fan may become damaged and you may be hurt. Keep children away from the indoor unit. Do NOT place any obstacles in front of the outdoor unit. If the remote control will not be used for a long time, remove the batteries. [. . . ] ) 5 E-10 To control the direction of the air flow, refer to pages 16 and 17. Heating Your Room ENGLISH You must select the Heat mode if you wish to adjust the: x Heating temperature x Fan speed when heating 1 If necessary, press the Result: (On/Off) button. x The POWER indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears. Result: x The indoor unit beeps each time you press the MODE button. x The air conditioner runs in HEAT mode. You can change modes at any time. Note 3 To adjust the temperature, press the TEMPERATURE buttons one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. Result: x Each time you press the TEMPERATURE buttons: - The temperature is adjusted by 1°C - The indoor unit beeps x The air conditioner starts heating, provided that the room temperature is lower than the selected temperature; the fan will, however, operate. 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed: Automatic (rotated : Low Medium High Result: x Each time you press the FAN button, the indoor unit beeps. x For the first 3 to 5 minutes, the fan does not operate until the air has been sufficiently warmed. Once the correct temperature has been reached, the fan will be automatically switched to the selected speed. ) 5 To control the direction of the air flow, refer to pages 16 and 17. E-11 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 To set the operating time, press the ON TIMER button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hour inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. x Blinking of the timer indicator stops. x The selected mode and the temperature on the display disappear after 10 seconds. x The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: x The air conditioner will run in the selected mode when it is turned on. To Cancel the On Timer 1 To cancel the On Timer, press the ON TIMER button one or more times until the timer setting disappears. 2 Press the (Set/Cancel) button. Note If you want to turn on the air conditioner before the timer reaches the setting time, press the (On/Off) button. E-18 Setting the Off Timer ENGLISH The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the OFF TIMER button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hour inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. x Blinking of the timer indicator stops. x The air conditioner will switch off automatically when the counter displayed on the remote control reaches the set time and disappears the Off timer setting. Example If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours: 1. [. . . ] A water leak or some other malfunction may occur if the heat exchanger freezes. Water may condense on and drip from the surface of the indoor unit if it is used for long periods. Indoor Humidity 80% or less - Low temperatures High humidity levels Mode Heating Cooling Drying Outdoor Temperature 0°C to 24°C approx. 18°C to 43°C approx. If the heating operation is used at below 0°C(outdoor temperature) then, it does not heat as its full capacity. [. . . ]