User manual DANBY DAC9003

[. . . ] Keep children away from the unit. 5 ALWAYS ensure that the power cable is in good condition. If the power cord is damaged in any way, it must be replaced by an authorized service technician. Do not use an extension cord with this or other appliance. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: x An authorized service center x The dealer from whom you purchased the air conditioner. 7 Do NOT place any blocking objects in front of the unit. [. . . ] air Theunit conditioner is fitted with a protection mechanism to prevent the from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up automatically after about three minutes. 2 If the HEAT indicator is not lit up on the unit: x Press the button on the remote control or x Press the MODE button on the unit one or more times until the HEAT indicator lights up x The unit beeps each time you press MODE. Result: x The air conditioner starts up in Heat mode. 3 You can change modes at any time. To adjust the temperature, press the or button on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the or button on the unit one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. x Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts heating if the room temperature is lower than the selected temperature. 4 To set the fan speed to. . . x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up Med Low Result: Each time you press a button, the unit beeps. 5 To control the direction of the air flow, refer to page 11. E-9 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. Remote Control Control Panel 2 If necessary, press the (On/Off) button. Start time 1hr 8hr Stop time Heating The temperature is decreased by 1°C after 1 hour. When it has been decreased by 2°C (after 2 hour), the temperature is maintained for 6 hours. To Cancel the Sleep Timer To cancel the timer, press: x on the remote control. x The SLEEP indicator is no longer displayed. x The air conditioner operates in the mode selected last. E-14 Operating Recommendations ENGLISH Here are a few recommendations that you should follow when using your air conditioner. Topic Heating performances Recommendation The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. If you find that the room is not warm enough, use an additional heating appliance. The air conditioner circulates warm air to heat your room; as a result, some time will be required after starting the air conditioner to warm the entire room. If necessary, set the air conditioner going a short time before you wish to use the room. When outside temperatures are low and humidity is high, frost may form in the unit's condensor when heating with your air conditioner. If this happens: x The unit stops heating x The air flow blades stop swinging x The Deice mode is triggered automatically for about five minutes x The DEICE indicator on the unit lights up red No intervention is required from you; after about five minutes, the air conditioner starts operating again normally. [. . . ] Replace the remote control batteries if necessary. Check that the correct operating mode has been selected COOL or HEAT. The room temperature may be too low or too high. Dust may be blocking the air filter; refer to page 17 or 18 for cleaning instructions. [. . . ]