User manual DANBY DAR440W

[. . . ] Cut access hole in shaded area shown in Figure 2. Pull electrical cable through hole into installation area. Air Gap * If required: · "Y" Branch Tailpiece and Connector Kit (See Step 4) · Air Gap Kit (See Step 4) · Fasteners for floor anchoring (See Step 9) Available at: Plumbing Supply Store Plumbing Supply Store Hardware Store Electric Shock Hazard Observe all local codes and ordinances for electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. [. . . ] (This kit is included on select models). Tip Over Hazard Do not use dishwasher until completely installed. Failure to follow this warning can result in serious injury. NOTE: It is not necessary to remove the outer door for installation. However, you might find it more convenient to do so. You can find directions for removing door in Step 10. Kickplate Assembly Adjustable Toeplate Connections For Electrical, Water, and Drain Installation Tips Tools and Materials Needed for Installation · · · · · · · · · · · · · · · Drill, Electric Driver, Socket 5/32", 1/4" , 5/16" Flaring Tool / Tube Cutter (for copper tubing) Flashlight Level Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers Safety Glasses Saw, Keyhole or 1/2", 11/2" to 2" Hole Cutters Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) Tape, Electrical or Duct Tape, Measuring Wire Stripper or Utility Knife Wrench, Hex-end Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing) 1 Water Inlet Valve Bottom Screws IMPORTANT: Do not cross drain, water, and electrical lines in front of dishwasher motor or frame. Locating the Connections 1. Review dimensions in Figure 3 to locate dishwasher's drain, water, and electrical connections. All connections must be made in shaded area in Figure 2. Kickplate (Insulation available some models) Figure 3 Figure 1 Left Side 25 Front 24 3. Locate water inlet valve behind kickplate on bottom left underside of unit. The valve has a 3/8" NPT female fitting. Wrap 90° elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve. Tighten elbow with a wrench, leaving elbow pointing toward rear of unit. To prevent bending of bracket or breaking of valve, avoid overtightening. Place door where it will not get scratched or damaged while completing installation. When ready to replace door, fit the slots on each side of top door edge over the tabs on the metal liner. Push on sides to insure the door is flat. Push up from bottom until there is no gap between door and console. See Figure 16c. Pump Motor Before starting the dishwasher, Use /4" Lag Screws (not included) 1 Figure 16c Console Metal Liner Door Leg Leveler Adjustment Chart Height of Number of Turns to Cabinet Opening Adjust Levelers 34" (86. 4cm) 0 341/8" (86. 7cm) 345/16" (87. 2cm) 34 /2" (87. 6cm) 1 Remove knockout plug in disposer Figure 10 2 6 9 The drain hose loop must be at least 32" high from the floor to insure proper drainage. Through Cabinet Through Wall Figure 15 For additional height add shims under levelers. Move dishwasher to front of installation area. Loosen the front and rear leveling legs by turning counterclockwise. Front levelers should allow 1/4" below underside of countertop. Finishing the Water Connection 7 Through Floor Junction Box (in place) Side View Note: If mounting your dishwasher to the countertop or to the floor is not a desirable option, you can order the side mount kit, 154477201, by contacting your dealer or parts supplier. This allows you to install the dishwasher by securing it to the cabinets or partitions on either side of the unit. The kit utilizes the front frame of the dishwasher to secure the unit to the cabinet or partitions. Appearance of console and door may vary from your model. Property Damage Do not solder within 6" of the water inlet valve. Damage to the plastic parts in the valve may occur. [. . . ] Failure to follow this warning could result in personal injury from exposed wiring. Pull out unit and check to see if drain hose is correctly attached to the drain pump assembly. If drain hose is not attached to drain pump, follow the instruction sheet (included with drain hose) on how to correctly install the drain hose to the drain pump assembly. Move unit back in place while routing drain hose through access hole. [. . . ]