User manual DANBY DDR301

[. . . ] Switching the Air Conditioner Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 6 6 7 7 x RECOMMENDATIONS FOR USE s s s s s Operating Recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Usually, the maximum permissible mains impedance will not be exceeded when the branch to the power outlet is fed from a junction box with a rated current of 32A. E-3 ENGLISH Air Conditioning Unit - Main Parts and Control Panel The design and shape are subject to change according to the model. Inner air flow blades (right/left orientation) Air outlet Air inlet (Inside) Air filter (The air filter is located in inside. ) Outer air flow blades (up/down orientation) Air inlet (Outside) Ventilation lever Power plug x The type of power plug may differ, depending on the local power supply. x The power plug may be not supplied depending on the model. Operating mode selection dial Temperature control dial Air flow blade swing switch E-4 Cooling Your Room ENGLISH 27°C ~ 23°C 29°C ~ 27°C 23°C ~ 18°C 27°C ~ 23°C 29°C ~ 27°C 23°C ~ 18°C E-5 You must select the Cool mode if you wish to lower the temperature in your room. You can also set the fan speed. 1 Select the operating mode and fan speed. High fan speed Low fan speed Result: Set the operating mode selection dial to. . . HI COOL LOW COOL x The air conditioner starts up in Cool mode. x The fan starts up at the speed selected. 2 You can change modes at any time. To adjust the temperature, turn the temperature control dial towards the right and the blue position. Possible temperatures: Between 18°C and 25°C inclusive. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 3 To control the direction of the air flow, refer to page 7. Heating Your Room You must select the Heat mode if you wish to heat your room to a specific temperature. You can also select the fan speed. 1 Select the operating mode and fan speed. High fan speed Low fan speed Result: Set the operating mode selection dial to. . . 28°C or less Outdoor Temperature 21°C to 43°C approx. Indoor Humidity 80% or less - If the air conditioner is used at. . . Higher temperature Lower temperature Then. . . The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. Higher humidity levels E-8 Water may condense on and drip from the surface of the unit if it is used for long periods. Cleaning Your Air Conditioner (F1 models) ENGLISH To get the best possible use out of your air conditioner, you must clean it regularly by two weeks to remove the dust on the air filter. Before cleaning your air conditioner, ensure that it is switched off and unplugged from the wall socket. 1 Hold the air filter handle, slightly pull it to the left side and open the front grille. The removal of the front grille makes it easier to clean the air conditioner. Open the grille as much as possible. CAUTION Removal and Reassembly of the Front Grille For user's safety, a safety clip has been installed in the front grille. 1 Grasp the lower part of the front grille and the air filter handle, then open the grille. 2 Remove the safety clip and the front grille. 3 When reassembling the front grille, you should install the safety clip again. Safety clip 2 Pull the air filter to the right side. 3 Remove all dust on the air filter with a vacuum cleaner or brush. 4 When you have finished, insert the air filter back into its original position. The air conditioner has two or three grille grooves depending on the model. 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. (Be sure not to use benzene, solvent or other chemical products. ) If you. . . Will not be using the air conditioner for a long period of time Then. . . x Set the operating mode selection dial to "FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. x Switch the air conditioner off and unplug it from the wall socket. Set the operating mode selection dial to "FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. E-9 Have not used the air conditioner for a long period of time Cleaning Your Air Conditioner (A1 models) To get the best possible use out of your air conditioner, you must clean it regularly by two weeks to remove the dust on the air filter. 1 Before cleaning your air conditioner, ensure that it is switched off and unplugged from the wall socket. Open the front grille by pulling on the tabs of the unit. The removal of the front grille makes it easier to clean the air conditioner. [. . . ] See the illustration below. Awning 75mm min. 300mm "A" 500mm 500mm 500mm Fence, wall or other obstacle Approx. 3° Model S J M "A" 180mm 220mm 240mm 750mm 150mm min. x If the wall is greater than 150mm thick, cut the wall back on a 45° angle if possible. Outdoor side 45° 45° Indoor side E-12 100mm or more Installation of the Drain Tube Fix the drain tube as shown in the figure. Rear Rubber cap Gasket Drain Tube Screws(2EA) Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area. x In the case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner. Example: High storage 1 2 Open the front grille ; refer to page 9 or 10. Remove the screw located at the lower section of the front grille. [. . . ]