User manual DANBY SAC8404DE

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. x Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. x Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] Confirm if any obstacles that may prevent the air flow are present near the air conditioner. IMPORTANT To operate the unit, the power switch is fitted to the wall must be set to ON. Using the Control Panel on the Indoor Unit You can operate with the indoor unit when you do not wish to or cannot operate the air conditioner with the remote control. You can : Adapt the On/Off, Temperature, Fan Speed, Energy Saving, Air Swing settings to your specific requirements. Example : Remote control is broken or lost. Using the Remote Control All air conditioner features except Lock function and Energy Saving mode can be controlled from your seat by using the remote control. You can : Note Adapt the Auto mode, Cool mode, Turbo mode and Fan Speed/Timer settings to your specific requirements. You must operate the Turbo, Long and Off Timer function with the remote control. E-8 Cooling Your Room You must select the Cool mode if you wish to adjust the : x Cooling temperature x Fan speed when cooling 1 If necessary, press the Result: (On/Off) button. x The power indicator on the control panel comes on. x The air conditioner starts up in the Cool mode. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Switched on x Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed on the control panel, press the remote control one or more times until it appears. Result: Note x The indoor unit beeps each time you press the x The air conditioner runs in the Cool mode. You can change modes at any time. button on the button. 3 To adjust the temperature, press the buttons on the remote control or buttons on the control panel one or more times until the required temperature is displayed. Possible temperatures are between 18OC and 30OC inclusive. Result: x Each time you press the buttons: - The temperature is adjusted by 1OC. x The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature. x The fan settings are adjusted automatically. x If you press the button in the Dry or the Fan mode that is changed with the Auto mode automatically. 3 To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 18OC and 30OC inclusive. Result: x Each time you press the buttons: - The temperature is adjusted by 1OC. - The indoor unit beeps. 4 If you wish to stop the Long function, press the Result: button again. x The air conditioner is reset automatically to the previous mode, temperature and fan settings. 5 To control the direction of the air flow horizontally, refer to page 16. E-12 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press the Result: (On/Off) button. x The power indicator on the control panel comes on. x The air conditioner starts up in the Cool mode. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Switched on x Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed on the control panel, press the remote control one or more times until it appears. x The air conditioner starts up in the Cool mode. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Switched on x Stopped lt will start up normally after three minutes. x The air conditioner runs in the Energy Saving mode. x The outer air flow blade moves up and down. IMPORTANT 2 Press the Result: 3 To adjust the temperature, press the buttons one or more times until the required temperature is displayed. [. . . ] buttons simultaneously for 2 To cancel the Lock function, press the 3 seconds once again. E-18 Operating Recommendation Here are a few recommendations that you should follow when using your air conditioner. Topic Power failure Recommendation If a power failure occurs when the air conditioner is operating, the unit is switched off. When the power returns, you must press the (On/Off) button to restart it. E-19 Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges, within which the air conditioner can be used. The automatic protection feature may be triggered and the air conditioner stopped. [. . . ]