User manual DATALOGIC GRYPHON I GD4100

[. . . ] GryphonTM I GD4100 Linear Imager Barcode Reader Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). [. . . ] The resulting message string would appear as follows: Scanned barcode data:12345 Resulting message string output: $12345 This option sets up to 20 characters each from the set of ASCII characters or any hex value from 00 to FF. To configure this feature, scan the ENTER/EXIT barcode to place the unit in Programming Mode, then the "Set Global Prefix" or "Set Global Suffix, " barcode followed by the digits (in hex) from the Alphanumeric characters in Appendix E, Keypad representing your desired character(s). If less than the expected string of 20 characters are selected, scan the ENTER/EXIT barcode to terminate the string. Reference the section, "Example: Setting a Prefix"on page 108, for more information. Exit programming mode by scanning the ENTER/ EXIT barcode once again. ENTER/EXIT PROGRAMMING MODE Set Global Prefix Set Global Suffix Make a mistake?Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL DEFAULT No Global Prefix Global Suffix = 0x0D Product Reference Guide 109 Data Editing Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. NOTE AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: · A close brace character (ASCII `]'), followed by. . . · A code character (see the table below), followed by. . . · A modifier character (the modifier character is symbol dependent). SYMBOLOGY UPC/EAN Code 39 and Code 32 Codabar Interleaved 2 of 5 Code 93 CHA R Ea A F I G SYMBOLOGY Code 128/GS1-128 DataBar Omnidirectional, DataBar Expanded Standard 2 of 5 ISBN Code 11 CHA R C e S Xb H a. UPC-A and UPC-E labels are converted to EAN 13 when adding AIM IDs. ISBN (X with a 0 modifier character) Figure 8. AIM ID Prefix Label ID AIM ID Bar Code Data Label ID Suffix 110 GryphonTM I GD4100 Global AIM ID Global AIM ID -- continued ENTER/EXIT PROGRAMMING MODE DEFAULT Global AIM ID = Disable Global AIM ID = Enable Product Reference Guide 111 Data Editing GS1-128 AIM ID If Global AIM ID is disabled, the AIM ID for GS1-128 can be enabled/disabled independently. The AIM ID for GS1-128 is a ]C1, ]C2 or ]C3. AIM IDs for other symbologies can be enabled/disabled independently as well. Contact Customer Support for assistance If Global AIM ID is disabled, the AIM ID for GS1-128 can be enabled/disabled independently. The AIM ID for GS1-128 is a ]C1, ]C2 or ]C3. AIM IDs for other symbologies can be enabled/disabled independently as well. Contact Customer Support for assistance. ENTER/EXIT PROGRAMMING MODE GS1-128 AIM ID = Disable DEFAULT GS1-128 AIM ID = Enable 112 GryphonTM I GD4100 Label ID Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x010xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs as a pre-loaded set (see "Label ID: Pre-loaded Sets"on page 113) or individually per symbology (see "Label ID: Set Individually Per Symbology"on page 115). [. . . ] Characters from 00 to 0x1F are sent as control character Ctrl+Capital Key, special keys are located from 0x80 to 0xA1. Special keys are located from 00 to 0x1F and characters from 0x80 to 0xFE are intended as an extended ASCII table (Microsoft Windows Codepage 1252 -- See page -314. ) Single Press and Release Keys In the following tables, Ar means Alt right pressed and Ar means Alt right released and so on. Definitions for other keys are Al (Alt left ), Cr (Control Right ) Cl (Control Left ) Sh (shift). This method can be used for combining Alt, Control or Shift with other keys. [. . . ]