User manual DATALOGIC MAGELLAN 1000I

[. . . ] Magellan® 1000i Omni-Directional Imaging Scanner Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). [. . . ] All other bar code symbology types read by the scanner will be transmitted as Code 128. Wand Emulation Bar Code Format The following format settings are required for the wand emulation interface. These settings have been pre-configured at the factory for Wand Emulation scanners. · · · · · · · UPC-A bar codes must include all 12 digits. UPC-E bar codes must contain 8 digits, including a system digit, 6 data digits, and the check digit. EAN-13 bar codes must have all 13 digits. EAN-8 bar codes must include all 8 digits. Code 39, Code 39 Full ASCII, and Pharmacode 39 bar codes must NOT contain start / stop characters. Codabar bar codes must include the start / stop characters, presented in the ABCD format. Interleaved 2 of 5 bar codes must have an even number of digits. 3-26 Magellan® 1000i Interface Features Wand Emulation -- cont. Bar/Space Polarity Low/High -- Black will be transmitted as a low voltage level (0 to +0. 7V) and space as high level (+2. 4 to +5. 25V). High/Low -- Black will be transmitted as a high voltage level (+2. 4 to +5. 25V) and space as low level (0 to +0. 7V). START / END PROGRAMMING BARCODES Bar/Space = Low/High Bar/Space = High/Low DEFAULT Wand Idle State This feature specifies the level of the wand output signal when idle. TTL logic levels: High voltage level (+2. 4 to +5. 25V) Low voltage level (0 to +0. 7V). START / END PROGRAMMING BARCODES Wand Idle State = Low DEFAULT Wand Idle State = High Product Reference Guide 3-27 Interface Related Features Wand Emulation -- cont. Signal Speed The speed of the transmission can be set. This selects the width of the minimum narrow bar. 330 microseconds 660 microseconds START / END PROGRAMMING BARCODES Signal Speed = 330mS Signal Speed = 660mS DEFAULT Transmit Trailing Noise The transmission of noise pulses after the label may be enabled or disabled. START / END PROGRAMMING BARCODES Disable Trailing Noise Enable Trailing Noise DEFAULT 3-28 Magellan® 1000i Interface Features Wand Emulation -- cont. Transmit Leading Noise The transmission of noise pulses before the bar code may be enabled or disabled. START / END PROGRAMMING BARCODES Disable Leading Noise Enable Leading Noise DEFAULT Symbology Conversion Wand Emulation can convert all bar codes to a single symbology. Choices are: No Conversion Convert to Code 39 Convert to Code 128 START / END PROGRAMMING BARCODES No Symbology Conversion DEFAULT Convert to C39 Convert to C128 Product Reference Guide 3-29 Interface Related Features Keyboard Wedge and USB Keyboard As a keyboard interface, the scanner supports most popular PCs and IBM terminals. The installation of the wedge is a fairly simple process that doesn't require any changes of software or hardware. All of the options in this section apply to the Keyboard Wedge, however, only some apply to USB Keyboard. NOTE Keyboard Layout The Keyboard Layout option supports many countries. For details about Keyboard Layout, please refer to your operating system manual. START / END PROGRAMMING BARCODES USA DEFAULT Belgium Britain Denmark France Germany 3-30 Magellan® 1000i Interface Features Keyboard Wedge -- cont. START / END PROGRAMMING BARCODES Italy Norway Portugal Spain Sweden Switzerland Japan 106 Key Hungary Czech Product Reference Guide 3-31 Interface Related Features Keyboard Wedge -- cont. START / END PROGRAMMING BARCODES Slovakia Romania Croatia Poland Caps Lock State Specifies the format in which the scanner sends character data. START / END PROGRAMMING BARCODES Disable Caps Lock DEFAULT Caps Lock "ON" Shift Lock "ON" 3-32 Magellan® 1000i Interface Features Keyboard Wedge -- cont. Power-On Simulation This feature does not apply to the USB Keyboard interface. NOTE All PCs check the keyboard status during the power-on Selftest. It is recommended that you enable this function if you are working without a keyboard installation. It simulates keyboard timing and passes the keyboard status to the PC during power-on. START / END PROGRAMMING BARCODES Disable Power-on Simulation DEFAULT ³ Enable Power-on Simulation Product Reference Guide 3-33 Interface Related Features Control Characters Specifies how the scanner transmits ASCII control characters to the host. Choices are: · · · Disable Control Characters Enable transmission of control characters to host Send characters between 00H and 1FH according to a special function-key mapping table. (This is used to send keys that are not in the normal ASCII set; a unique set is provided for each available scancode set. [. . . ] The remaining tables in this chapter provide the function key maps associated with each of the scancode sets. Keyboard Model Cross Reference TransScancode mission Set Protocol Func. Use Key Country Map Mode Support PC/XT Scan Set 1 No No Model Type PC/XT Foreign ALT Mode AT; PS/2 25-286; PS/2 30-286; PS/2 50, 50Z; PS/2 60, 70, 80, 90, 95 Foreign ALT Mode PS/2 25 and 30 Foreign ALT Mode PC/XT U. S. Mode AT; PS/2 25-286; PS/2 30-286; PS/2 50, 50Z; PS/2 60, 70, 80, 90, 95 U. S. [. . . ]