User manual DATALOGIC POWERSCAN 7000 2D IMAGER

[. . . ] PowerScan 7000 2D Imager Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). [. . . ] The cursor is not moved by the FB command. . zz where nn is a count of the number of suppressed characters in the list and xxyy . . zz is the list of characters to be suppressed. (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) FC Disables suppress filter and clear all suppressed characters. E4 Replaces up to 15 characters in the data string with user specified characters. Replacement continues until the E5 command is encountered. Syntax = E4nnxx1xx2yy1yy2. . . zz1zz2 where nn is the total count of both characters to be replaced plus replacement characters; xx1 defines characters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. FE Compare character in current cursor position to the character "xx. " If characters are equal, increment cursor. If characters are not equal, no format match. Syntax = FExx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4. ) EC Check to make sure there is an ASCII number at the current cursor position. If character is not numeric, format is aborted. 5-4 PowerScan 7000 2D Data Format Editor Introduction ED Check to make sure there is a non-numeric ASCII character at the current cursor position. If character is numeric, format is aborted. Syntax = ED. D ata Form at Editor Enter Data Format * Default Data Format Clear One Data Format Clear All Data Formats Save Discard D ata Form atter When Data Formatter is turned off, the bar code data is output to the host as read (including prefixes and suffixes). Default = Data Formatter On, but Not Required. * Data Formatter On, but Not Required Data Formatter Off When Data Formatter is required, all input data must conform to an edited format or the imager does not transmit the input data to the host device. Data Format On, Format Required Product Reference Guide 5-5 Data Formatting Alternate Data Formats Alternate formats allow you "single shot" capability to scan one bar code using a different data format than your primary format. When data formats are programmed (see page 5-2), you must input whether you are programming the primary format, or an alternate format numbered 1, 2, or 3. An alternate format is initiated by scanning one of the 3 alternate format bar codes below. The imager will scan the next bar code, formatting the data with the selected alternate format, then revert immediately to the primary format. Alternate Data Format 1 Alternate Data Format 2 Alternate Data Format 3 5-6 PowerScan 7000 2D Chapter 6 Symbologies This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. Linear Symbologies Australian Post Aztec Code Enable British Post Canadian Post China Post Enable Codabar Enable Codablock F Enable Code 11 Enable Code 128 Enable Code 16K Enable Code 2 of 5 Enable Code 39 Enable Code 49 Enable Code 93 Enable Data Matrix Enable EAN/JAN-13 Enable EAN/JAN-8 Enable EANUCC Composite Codes IATA Code 2 of 5 Enable Interleaved 2 of 5 Enable Japanese Post Kix (Netherlands) Post Korea Post Matrix 2 of 5 Enable MaxiCode Enable MicroPDF417 Enable MSI Enable PDF417 Enable Planet Code Plessey Code Enable PosiCode A and B Enable Postnet QR Code Micro QR Code RSS Expanded Enable RSS Limited Enable RSS-14 Enable TCIF Linked Code 39 (TLC39) Telepen UPC-A Enable UPC-A/EAN-13 with Extended Coupon Code Product Reference Guide 6-1 Symbologies Linear Symbologies All Symbologies If you want to decode all the symbologies allowable for your imager, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. All Symbologies On All Symbologies Off Message Length Description You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code doesn't match the valid reading length, the imager will issue an error beep. You may wish to set the same value for minimum and maximum length to force the imager to read fixed length bar code data. [. . . ] Length Code 16K Code 16K Minimum (2 - 80) *4 Maximum (2 - 80) *48 *Off On Default All Codablock F Settings *Off On Minimum (1 - 2048) *1 Maximum (1 - 2048) *2048 Default All Code 16K Settings *Off On RSLDFT RSLENA0 RSLENA1 RSEDFT RSEENA0 RSEENA1 RSEMIN## RSEMAX## POSDFT POSENA0 POSENA1 POSLIM0 POSLIM1 POSLIM2 POSMIN## POSMAX## TRIENA0 TRIENA1 CBFDFT CBFENA0 CBFENA1 CBFMIN#### CBFMAX#### 16KDFT 16KENA0 16KENA1 6-30 6-30 6-30 6-31 6-31 6-31 6-31 6-31 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-33 6-33 6-33 6-33 6-33 6-33 6-33 6-34 6-34 6-34 10-20 PowerScan 7000 2D Menu Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default Minimum (0 - 160) *1 Maximum (0 - 160) *160 Default All Code 49 Settings Off *On Minimum (1 - 81) *1 Maximum (1 - 81) *81 Default All PDF417 Settings *On Off Minimum (1-2750) *1 Maximum (1-2750) *81 Default All Micro PDF417 Settings *On Off Minimum (1-366) *1 Maximum (1-366) *366 On *Off On *Off Minimum (1-2435) *1 Maximum (1-2435) *2435 RSS Emulation EANUCC-128 Emulation *EANUCC Emulation Off On *Off On *Off Page 6-34 6-34 6-35 6-35 6-35 6-35 6-35 6-36 6-36 6-36 6-36 6-36 6-37 6-37 6-37 6-37 6-37 6-37 6-37 6-37 6-37 6-38 6-38 6-39 6-39 6-39 6-39 6-39 6-40 6-40 Code 16K Msg. Length MicroPDF417 MicroPDF417 MicroPDF417 Msg. Length EANUCC Composite Codes UPC/EAN Version EANUCC Composite Codes Msg. Length EANUCC Emulation TCIF Linked Code 39 (TLC39) Postnet 16KMIN### 16KMAX### C49DFT C49ENA0 C49ENA1 C49MIN## C49MAX## PDFDFT PDFENA1 PDFENA0 PDFMIN PDFMAX MPDDFT MPDENA1 MPDENA0 MPDMIN MPDMAX COMENA1 COMENA0 COMUPC1 COMUPC0 COMMIN COMMAX EANEMU2 EANEMU1 EANEMU0 T39ENA1 T39ENA0 NETENA1 NETENA0 Product Reference Guide 10-21 Serial Programming Commands Serial Command # Indicates a numeric entry Selection Setting * Indicates default Transmit *Don't Transmit On *Off Transmit *Don't Transmit On *Off On *Off On *Off On *Off On *Off Default All China Post Settings *Off On Minimum (2 - 80) *4 Maximum (2 - 80) *80 Default All Korea Post Settings *Off On Minimum (2 - 80) *4 Maximum (2 - 80) *48 Default All QR Code Settings On *Off Page 6-40 6-40 6-41 6-41 6-41 6-41 6-42 6-42 6-42 6-42 6-42 6-42 6-43 6-43 6-43 6-43 6-43 6-44 6-44 6-44 6-44 6-44 6-45 6-45 6-45 6-45 6-45 6-46 6-46 Postnet Check Digit Planet Code Planet Code Check Digit British Post Canadian Post Kix (Netherlands) Post Australian Post Japanese Post China Post China Post China Post Msg. [. . . ]