User manual DATALOGIC QUICKSCAN QS6500BT

[. . . ] QuickScan® QS6500/QS6500BT Product Reference Guide Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic Scanning"). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. [. . . ] DEFAULT SETTING FOR THIS FEATURE: 00 (None) Set Truncation: Leading Set Truncation: Ending SET END 6-58 QuickScan® QS6500/QS6500 BT RSS Limited RSS Limited -- continued Code I. D. for this symbology consists of one or two user-selectable ASCII characters. It can be appended previous to or following the transmitted RSS Limited bar code data depending on how this feature is enabled. Example: Setting the RSS Limited Code I. D. To configure this feature: 1. Determine which character(s) you would like to use to represent the RSS Limited symbology. Reference Appendix A, ASCII Conversion Chart to find the corresponding hex values for your chosen character(s). In this example we'll set a Code I. D. of "RL" to represent RSS Limited. The value from the table corresponding to `'R' is 52 and the value for `L' is 4C. These values will be used in a step to follow. Turn to Appendix B, Alpha-Numeric Pad and scan the bar codes `5' and `2' (the value determined in an earlier step to represent `R'). Then scan the bar codes `4' and `C' (hex equivalent for `L'). Scan the SET bar code to accept the digits scanned. Turn to the Data Editing chapter and scan the CODE ID POSITION: BEFORE BAR CODE DATA label. Features configured using the Data Editing chapter are universal and will affect all symbologies. Scan the END bar code to exit Programming Mode. The resulting message string for scanned RSS Limited labels would appear as follows: Scanned bar code data: 0123456789123 Product Reference Guide 6-59 Symbologies Resulting message string output: RL0123456789123 RSS Limited -- continued START STATE Set RSS Limited Code I. D. Character(s) BARCODE DEFAULT SETTING FOR THIS FEATURE: RL (52hex, 4C hex) Select 0000 to disable Code ID for this symbology only. SET END 6-60 QuickScan® QS6500/QS6500 BT RSS Limited RSS Limited -- continued RSS Limited Data Group Characters Once you've pre-set your desired Data Group Characters1 using the Data Group Characters feature found in Chapter 5, Data Editing, you can choose to output up to two of those pre-sets whenever an RSS Limited bar code is scanned. The options in this section set Data Group Characters for the RSS Limited symbology ONLY. If you wish to enable this feature for additional symbologies, turn to the options in the section specific to the other symbology(s). NOTE To set this feature: 1. Determine which Data Group pre-set(s) to output. You can select up to two from the following: Data Group 1 * Data Group 2 * Data Group 3 * Data Group 4 For example, your choice might be Data Group 2 only; Data Groups 1 and 3; Data Groups 3 and 4; or no Data Groups. Scan the START bar code to place the imager in Programming Mode. Scan the SET RSS Limited DATA GROUP CHARACTERS bar code. Turn to Appendix B, Alpha-Numeric Pad and scan the digits representing the Data Group designation(s) chosen in the first step above. [. . . ] USB Function Key Usage Map ASCII 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 Key value NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 Usage Name ALT right Make ALT right Break F11 F12 GUI right Make GUI right Break CTRL right Make CTRL right Break BS TAB right RIGHT arrow (inner keypad) TAB left Enter (right keypad) CR INSERT (inner keypad) PAGE UP (inner keypad) PAGE DOWN (inner keypad) HOME (inner keypad) LEFT arrow (inner keypad) Modifier/ Scancode 40h 00h 00h 00h1 00h 44h 00h 45h 80h 00h 00h 00h1 10h 00h 00h 00h1 00h 2Ah 00h 2Bh 00h 4Fh 02h 2Bh 00h 58h 00h 28h 00h 49h 00h 4Bh 00h 4Eh 00h 4Ah 00h 50h Product Reference Guide C-1 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DOWN arrow (inner keypad) UP arrow (inner keypad) F6 F1 F2 F3 F4 F5 ESC F7 F8 F9 F10 00h 51h 00h 52h 00h 3Fh 00h 3Ah 00h 3Bh 00h 3Ch 00h 3Dh 00h 3Eh 00h 29h 00h 40h 00h 41h 00h 42h 00h 43h Table C-2. Keyboard Model Cross Reference TransScancode mission Set Protocol Func. Use Key Country Map Mode Support Scan Set 1 No No Model Type PC/XT Foreign ALT Mode AT; PS/2 25-286; PS/2 30-286; PS/2 50, 50Z; PS/2 60, 70, 80, 90, 95 Foreign ALT Mode PS/2 25 and 30 Foreign ALT Mode PC/XT U. S. Mode AT; PS/2 25-286; PS/2 30-286; PS/2 50, 50Z; PS/2 60, 70, 80, 90, 95 U. S. [. . . ]